User manual CLARION MSS430

[. . . ] · Before installation, disconnect the (­) negative lead from the vehicle's battery. · Use only supplied screws and hardware. Make sure all connections and components are fastened securely. · At the proposed installation sites, make sure there is adequate space to accommodate both MSS430 and the Control Station dimensions. [. . . ] The MSS430 requires low-level signal inputs only. 1 A/V INPUT 1 (3 -RCA Jacks) Use a triple RCA A/V cable (not supplied) to connect video and stereo audio from the primary video source (e. g. , Clarion VDH910 VCR, VS715 DVD Player, etc. ) to the MSS430 A/V Selector. Adjust the input gain controls so that the source's level 10 2 A/V INPUT 2 (3 -RCA Jacks) Same as A/V Input 1. Use these jacks to connect a second video source (e. g. , video game console, TV Tuner, etc. ) OWNER'S MANUAL/INSTALLATION GUIDE 3 A/V INPUT 3 (3 -RCA Jacks) Same as A/V Input 1. Use these jacks to connect a third video source. 5 POWER INPUT CONNECTOR (4-Pin Molex) Connect the enclosed Molex pigtail to the vehicle's power, ground, and back-up light circuits, (see Figure 3 on page 6). 4 A/V INPUT 4 (3 -RCA Jacks) Same as A/V Input 1. Use these jacks to connect a fourth video source. NOTE: When using a optional Clarion Rear Vision Camera, the video connection must be connected to A/V Input 4 to function properly with the reverse wire. See Figure 7 on page 8 for connection configuration. When +12Vdc is applied to the reverse wire (Pin 4), the MSS430 will automatically override Control Station 1's video selection and switch directly to A/V Input 4. The LED indicator will blink to show that the reverse function is active. The video signal will automatically override any other selection that is being viewed on Monitor 1. When voltage is removed from the reverse wire, the monitor will automatically switch back to the original source selected. 11 SOURCE COMMANDER MSS430 DESCRIPTION OF MSS430 REAR CONNECTORS (CONT'D) 6 7 8 9 0 q w e r Figure 11. The MSS430's A/V Outputs and Power connectors. 6 CONTROL STATION 1 (6 -Pin Connector) The Control Station connected to this port provides control and selection of Zone 1 audio/video sources. The Control Station connected to this port provides control and selection of Zone 3 audio/video sources. 9 A/V OUTPUT 1 (3 -RCA Jacks) Use this output when connecting the MSS430 to an external (NTSC-composite type) video monitor for Zone 1. 7 CONTROL STATION 2 (6 -Pin Connector) The Control Station connected to this port provides control and selection of Zone 2 audio/video sources. 0 MONITOR 1 OUTPUT (2 -Pin Connector) Connect to the monitor's +12 V and ground for Zone 1. 8 CONTROL STATION 3 (6 -Pin Connector) 12 OWNER'S MANUAL/INSTALLATION GUIDE q A/V OUTPUT 2 (3 -RCA Jacks) Use this output when connecting the MSS430 to an external (NTSC-composite type) video monitor for Zone 2. DESCRIPTION OF CONTROL STATION 1 w MONITOR 2 OUTPUT (2 -Pin Connector) Connect to the monitor's +12 V and ground for Zone 2. e A/V OUTPUT 3 (3 -RCA Jacks) Use this output when connecting the MSS430 to an external (NTSC-composite type) video monitor for Zone 3. 4 2 3 Figure 12. The Control Station's Power button, source LED indicators, and Source Select buttons. r MONITOR 3 OUTPUT (2 -Pin Connector) Connect to the monitor's +12 V and ground for Zone 3. 1 SOURCE SELECT LEDs When illuminated, each LED indicates which A/V source is selected. Press the SOURCE SELECT button to change source selection and the corresponding LED will illuminate. 13 SOURCE COMMANDER MSS430 2 SOURCE SELECT Button Press the SOURCE SELECT button one or more times to step through the different Audio/Video inputs. Each LED illuminates to confirm the source selected. Press and hold the Power button for 2 to 3 seconds to power down the monitor at each of the Control Stations. 4 Mounting Bezel Outer mounting bezel around each Control Station allows for easy installation. (see page 6 for intallation information). 3 POWER Button When ignition is applied to the MSS430's ignition lead, all control stations are automatically set into the Stand-By mode (no power output from the monitor's power connector). Press the POWER button on any Control Station and the source LED will illuminate and the monitor will power on. NOTE: Control Stations a). If the Ignition is shuts down while the Control Stations are in use, the Control Stations will not automatically turn on when the ignition is activated again. After system and individual control station power is on, power on the video game player and insert a desired game cartridge. [. . . ] vehicle is in reverse gear. 19 SOURCE COMMANDER MSS430 MSS430 SPECIFICATIONS Audio Specifications Maximum Output: Frequency Response: S/N Ratio (A-wtd): Input Sensitivity: Input Impedance: Input/Output Gain: Video Specifications ­ 4 Vp-p (peak to peak) 30 Hz to 25 kHz 60 dB 1. 0 Vp-p (peak to peak) 10k Ohms 0dB +/-2dB at Max volume with 600 Ohm load. 1. 0 Vp-p +/- 20% (peak to peak) 39 Hz to 5. 5 MHz 0dB +/-2dB with 75 Ohm load 0Vp-p +/- 20% (peak to peak) 75 Ohms 10 Vd c - 13 Vd c 1. 6 A Dimensions (w x h x d): 9. 84 x 1. 06 x 5. 24 in. (250 x 27 x 133 mm) CONTROL SPECIFICATIONS Dimensions (w x h x d): 1. 7 x 2. 6 x . 60 in. (43 x 66 x 15 mm) Mounting Depth: Mounting Hole Diam. : . 63 in. [. . . ]