User manual CLARION MSS7100 INSTALLATION MANUAL

[. . . ] · Use extreme caution when drilling around electrical wiring, brake lines, and fuel lines. Check clearances on both sides of a planned installation surface before drilling any holes or installing any screws. · Always wear protective eyewear when using tools. · Use only high-quality RCA cables that are no longer than necessary for direct connections to other components in the system. Extra-length audio and video cables can cause signal loss and act as an "antenna" for noise. [. . . ] Only use a soft (cotton or other non-static) cloth to wipe off fingerprints or other imprints from the faceplate or remote control. · Do not subject the unit to direct sunlight or an extremely hot environment (e. g. , closed windows on a hot summer day, direct path of heater vent, etc. ). · Avoid using the products under the following conditions: ­ After extended parking on an extremely hot or cold day ­ Near strong magnetic fields ­ In an environment with excessive humidity, dust, or vibration (e. g. , off-road travel, etc. ) 4 OWNER'S MANUAL/INSTALLATION GUIDE INSTALLATION AND WIRING Parts List Installing the MSS7100 · (1) Source Commander MSS7100 A/V Selector · (3) Control Stations · (3) Control Station Cables · (2) Mounting L-Brackets R M4 x 15 Self-tapping Sheet Metal Screw (4 supplied) · (4) M4 x 8 Pan Head Machine Screws · (4) M4 x 15 Self-tapping Sheet Metal Screws · (1) 4-pin Molex Power Connector · (3) 2-pin Monitor Power Connectors · Owner's Manual/Installation Guide L V R L V R L V R L V POW ER · Warranty Registration Card M4 x 8 Pan Head Machine Screws (4 supplied) Figure 1. Installing the MSS7100. 5 SOURCE COMMANDER MSS7100 Installing the Control Station MSS7100 Wiring for the 4-Pin Power Harness Ignition Switch Red Green Black To Ground Fuse Reverse Switch + Battery Reverse Lights (on vehicle's rear) To Vehicle Circuits 34 1 Reverse (Green) None Ground (Black) Ignition (Red) 2 3 4 Opening Mounting Bazel Control Station Figure 2. Installing the Control Station in a center console. END VIEW 12 Figure 3. Wiring and pinouts for the 4-pin power harness. 6 OWNER'S MANUAL/INSTALLATION GUIDE INSTALLATION AND WIRING (CONTINUED) MSS7100 Wiring for DVD Disc Player MSS7100 Wiring for VCR R L V R L V R L V R L V R L V R L V R L V R L V Clarion VDH910 Videocassette Recorder (rear view) Figure 4. Wiring diagram using a VS715 DVD player. Figure 5. Wiring diagram for a VDH910 VCR Input. 7 SOURCE COMMANDER MSS7100 MSS7100 Wiring for TV Tuner Input MSS7100 Wiring for Rear Vision Camera R L V R L V R L V R L V R L V R L V R L V R L V Figure 6. Wiring diagram for a TTX001 TV Tuner. Figure 7. Wiring diagram for a Clarion Rear Vision Camera. 8 OWNER'S MANUAL/INSTALLATION GUIDE Power Connector Pinouts MSS7100 Video and Power Connector Pinouts A/V INPUT 1 ~ 4 RCAs 34 END VIEW Center Connductor is signal (+), Outside conductor is signal ground (-). POWER 4-Pin Connector (Male Pins) 1 2 3 4 Reverse (Green) None Ground (Black) Ignition (Red) A/V OUTPUT 1 ~ 3 RCAs Center Connductor is signal (+), Outside conductor is signal ground (-). 12 END VIEW 12 MONITOR OUTPUT 2-Pin Connector (Male Pins) 1 2 Negative Lead Positive Lead POWER INPUT 4-Pin Molex 43 Chassis View MONITOR OUTPUT 2-Pin Connector Chassis View 1 2 3 Reverse (Green) None Ground (Black) Ignition (Red) 1 2 Negative Lead Positive Lead 21 Figure 8. 4- and 2-pin Molex Power connector pinouts. 4 21 Figure 9. Press the Power button on the Control Station again. The Control Station will power up and remember the last source selected. 14 OWNER'S MANUAL/INSTALLATION GUIDE APPLICATIONS INPUT CONFIGURATIONS R L V R L V R L V R L V Rear Vision Camera CCA DNG VER VS715 VDH910 Figure 13. Using the MSS7100 Input Connectors. 15 SOURCE COMMANDER MSS7100 APPLICATIONS OUTPUT CONFIGURATIONS VMA7191 IR to TTX001 Control Station 3 VMA7191 IR to VDH910 Control Station 2 WH200 IR HEADPHONES R L V R L V R L V R L V Control Station 1 TVX5653 CAA-389 (optional) Figure 14. Using the MSS7100 Output Connectors. 16 OWNER'S MANUAL/INSTALLATION GUIDE OPERATING THE MSS7100 SYSTEM Reverse Mode (Control Station 1 ONLY) Viewing A Videocassette When using this control station with an optional Rear Vision Camera and CAA188 power supply, the camera's source will automatically switch when the car is put into the reverse gear. The LED indicator will flash designating the Reverse Mode and the monitor will display the video signal from the Rear Vision Camera. NOTE: Rear Vision Camera Connections a). The Rear Vision Camera's video output from the CAA188 must be connected directly to A/V Input 4 only. (see MSS7100 Wiring for Rear Vision Camera on page 8). When the vehicle is taken out of the reverse gear, the last video source chosen, before the reverse mode, is displayed and the source LED is illuminated constantly. 1. After system and individual control station power is on, insert a videocassette in the VCR and press PLAY on the corresponding IR Remote Control. Use the IR remote controls to control the VCR functions through the monitor's IR Sensor. [. . . ] No sound from in-dash monitor CAA389 not connected properly. Camera not connected Connect a Clarion Rear Vision properly. Camera to the A/V INPUT 4 video connector. No Power to CAA188 Check power and ground connections to CAA188. Reverse Wire not con- Check for proper connection and nected on CAA188 +12 V on Reverse Wire when camera power supply. [. . . ]