Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual CLARION PSW-GM-SU. We hope that this CLARION PSW-GM-SU user guide will be useful to you.
Lastmanuals help download the user guide CLARION PSW-GM-SU.
Manual abstract: user guide CLARION PSW-GM-SUINSTALLATION MANUAL
Detailed instructions for use are in the User's Guide.
[. . . ] The woofer supplied with this system uses a voice coil with rated impedance of 2 ohms, and therefore is not considered a standard woofer. Replacing the woofer with any driver having an impedance greater than 2 ohms will yield lower power output from the amplifier, and is not recommended.
PROCEDURE
Proper installation of this product requires proper tools and knowledge of car audio principles. If you are not comfortable performing any of the outlined tasks below, contact a professional installation facility to perform the work.
OUTLINE
· · · · · Remove the head unit. [. . . ] Connect the BLACK wire on "T" harness to radio chassis.
· STEP 3: Route the wire harness from the radio to transmission hump of the vehicle. ·STEP4:
Connect the amplifier ground wire to a clean chassis ground near the subwoofer enclosure. Turn on the system and be sure all speakers are working properly. Set the subwoofer amplifier gain to a suitable level.
Ib. WIRING USING THE SUPPLIED HARNESS
· STEP 1: Remove the Radio. Yellow: Connect to Constant 12V Power Black: Connect to Radio Ground or Chassis Blue: Connect to Amp/Antenna Turn-on Lead Green: Connect to Left Rear Speaker (+) Positive Lead Green/Black: Connect to Left Rear Speaker (-) Negative Lead Violet: Connect to Right Rear Speaker (+) Positive Lead Violet/Black: Connect to Right Rear Speaker (-) Negative Lead · STEP 3: Route the wire harness from the radio to transmission hump of the vehicle. ·STEP 4:
Connect the amplifier ground wire to a clean chassis ground near the subwoofer enclosure. Turn on the system and be sure all speakers are working properly. Set the subwoofer amplifier gain to a suitable level.
2
II.
RUN WIRE HARNESS
A. Route harness straight down from the radio to the vehicle floor. Put a small slit in the carpet about 12" away from the black floor vents. Route harness through the slit in the carpet. Ground the 8" black wire to the vehicle floor (be sure to use a wire wheel or sand paper if grounding to a painted surface).
III. INSTALL THE BRACKETS TO THE ENCLOSURE
A. Align the (2) flat 4-hole brackets to the dimples on the bottom of the enclosure. Attach each bracket with two pilot point screws (one hole of the bracket should extend out past the enclosure). [. . . ] Screw in the front two bracket to the vehicle floor (or duct work depending on application) using the supplied 1" self-taping screws. Fold carpet slits back over to conceal the brackets. Attach the rear `L' bracket to the vehicle using (2) pilot point screws. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE CLARION PSW-GM-SU
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual CLARION PSW-GM-SU will begin.
