Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual CLARION PSWFF150. We hope that this CLARION PSWFF150 user guide will be useful to you.
Lastmanuals help download the user guide CLARION PSWFF150.
Manual abstract: user guide CLARION PSWFF150INSTALLATION MANUAL
Detailed instructions for use are in the User's Guide.
[. . . ] The woofer supplied with this system uses a voice coil with rated impedance of 2 ohms, and therefore is not considered a standard woofer. Replacing the woofer with any driver having an impedance greater than 2 ohms will yield lower power output from the amplifier, and is not recommended.
PROCEDURE
Proper installation of this product requires proper tools and knowledge of car audio principles. If you are not comfortable performing any of the outlined tasks below, contact a professional installation facility to perform the work.
OUTLINE
· · · · · · Remove the head unit. [. . . ] ·STEP 4: Connect the amplifier ground wire to a clean chassis ground near the subwoofer enclosure.
STEP 5: TEST and SET the GAIN. Turn on the system and be sure all speakers are working properly. Set the subwoofer amplifier gain to a suitable level.
Ib. WIRING USING THE SUPPLIED HARNESS
· STEP 1: Remove the Radio. Yellow: Connect to Constant 12V Power Black: Connect to Radio Ground or Chassis Blue: Connect to Amp/Antenna Turn-on Lead Green: Connect to Left Rear Speaker (+) Positive Lead Green/Black: Connect to Left Rear Speaker (-) Negative Lead Violet: Connect to Right Rear Speaker (+) Positive Lead Violet/Black: Connect to Right Rear Speaker (-) Negative Lead · STEP 3: Route the wire harness from the radio to the rear passenger side of the vehicle. ·STEP 4: Connect the amplifier ground wire to a clean chassis ground near the subwoofer enclosure.
STEP 5: TEST and SET the GAIN. Turn on the system and be sure all speakers are working properly. Set the subwoofer amplifier gain to a suitable level.
2
II. REMOVE FLOOR VENT TRIM COVER
A Remove the (3) panel hold down trees located on each side of the black floor vent cover.
III. Insert harness through radio housing opening in the dash and feed straight down to floor. Ground the BLACK wire on the harness to the floor of the truck (use wire wheel or sand paper to bare metal of ground location). Plug-in the "T" harness to the factory radio harness and the source side of the 3' harness in the dash -or- hard wire "Pigtail" harness.
IV. Place subwoofer enclosure into the vehicle and plug in the Clarion harness to the harness connector on the subwoofer enclosure. Turn on the radio and test the subwoofer enclosure. Gain the enclosure using a small screwdriver (gain control is located next the harness connector on the enclosure). Unplug and remove the enclosure.
V.
REINSTALL FLOOR VENT TRIM COVER
A. [. . . ] so that the foam is slightly being compressed uniformly around the I. P. ).
VIII. Position enclosure into proper location. Cut a "U" shaped slit in the carpet at the two bracket locations. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE CLARION PSWFF150
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual CLARION PSWFF150 will begin.
