User manual CLARION PSWFRGR INSTALLATION MANUAL

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual CLARION PSWFRGR. We hope that this CLARION PSWFRGR user guide will be useful to you.

Lastmanuals help download the user guide CLARION PSWFRGR.

Download

Manual abstract: user guide CLARION PSWFRGRINSTALLATION MANUAL

Detailed instructions for use are in the User's Guide.

 [. . . ] PREPARATION
Parts list
(Qty) Component Preassembled (1) Roto-molded subwoofer enclosure (1) 8"; 2 ohm subwoofer (1) 100W class "D" amplifier (1) Speaker grille Loose Components (1) 17' wire harness w/ pigtail style connector (2) Attachment brackets (4) 3/4" pilot point wafer Phillips head screws (4) 1" self taping wafer Phillips head screws (1) 1/2" ground screw (1) Star washer

WIRING:

Note: Installer MUST disconnect speaker-input leads to amplifier when using line-level input

OVERVIEW
The Clarion Camouflage subwoofer system provides for the installation of a low frequency driver in an enclosure which is powered by a small low current,  high power class "D" (Digital) amplifier. The advantage to using this type of amplifier is in the low current consumption of the amplifier at high power levels. The class "D" amplifier provided with this system will produce a rated 100W into a 2 ohm load.  [. . . ] Please refer to section Ia and Ib for each. 

· STEP 1: Remove the Radio. · STEP 2: Connect the "T" Harness. Plug the "T" harness in line with the radio wiring. Connect the BLACK wire on "T" harness to radio chassis. 

· STEP 3: Route the wire harness from the radio to transmission hump of the vehicle. ·STEP 4: Connect the amplifier ground wire to a clean chassis ground near the subwoofer enclosure. 
STEP 5: TEST and SET the GAIN. Turn on the system and be sure all speakers are working properly. Set the subwoofer amplifier gain to a suitable level. 

Ib. WIRING USING THE SUPPLIED HARNESS
· STEP 1: Remove the Radio. Yellow: Connect to Constant 12V Power Black: Connect to Radio Ground or Chassis Blue: Connect to Amp/Antenna Turn-on Lead Green: Connect to Left Rear Speaker (+) Positive Lead Green/Black: Connect to Left Rear Speaker (-) Negative Lead Violet: Connect to Right Rear Speaker (+) Positive Lead Violet/Black: Connect to Right Rear Speaker (-) Negative Lead · STEP 3: Route the wire harness from the radio to transmission hump of the vehicle. ·STEP 4: Connect the amplifier ground wire to a clean chassis ground near the subwoofer enclosure. 
STEP 5: TEST and SET the GAIN. Turn on the system and be sure all speakers are working properly. Set the subwoofer amplifier gain to a suitable level. 

2

II. 

RUN WIRE HARNESS

A. Route wire harness behind the drivers seat. Plug in Clarion"T" harness or hard wire pigtail harness in the dash. 

III.  [. . . ] Press enclosure firmly against the rear wall. Screw in brackets to the vehicle floor using the (4) supplied 1" self tapping screws. 

VI. Then do the process in reverse order. 

Clarion Corporation of America 661 West Redondo Beach Blvd Gardena,  CA 90247 800-Go-Clarion www. clarion-usa. com © 2000 Clarion Corporation,  Gardena,  CA

10 - PSWFRGR Rev.  [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE CLARION PSWFRGR

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual CLARION PSWFRGR will begin.