User manual CLIFFORD 100

[. . . ] The system then automatically resets and rearms. Patented Malfunction AutoBypassTM --In the unlikely event of a trigger or sensor malfunction, your ACE 100 will automatically bypass the malfunction and arm all other points to continue relentless protection of your vehicle. Patented Prior Intrusion Attempt Alert -- When you return to your vehicle and remotely disarm your ACE 100, a special chirp and parking light flash sequence will audibly and visually alert you from a distance if an intrusion attempt was foiled while you were away. Patented Remote Control Code Learning -- Just a few flicks of a switch lets you match to the system up to 4 different 2-button/3-channel Clifford remote controls. [. . . ] Button II (channel 2) can optionally pop the trunk or activate another optional accessory. TO DISARM THE SYSTEM . . TO REMOTELY CONTROL AN OPTION AutoArmingTM If this feature is enabled and you forget to remotely arm, ACE 100 automatically arms itself 30 seconds after the doors are closed. For your convenience, if you re-open any door(s) within the 30-second countdown, AutoArming will restart from the beginning once all doors are closed. ACE 100 has these additional AutoArming features: AutoArming enable/disable: If you prefer, you may deactivate or reactivate the AutoArming feature. See User-selectable features on page 6. AutoArm & Lock: To ensure you can't accidentally lock your keys inside the car, the system is factory-set not to lock* the doors upon AutoArming. To change this setting, see User-selectable features on page 6. * Some vehicles require optional relays to control the vehicle's power locks. 3 Valet mode Whenever the system is put in valet mode, all of the system's security features are switched off. At various times, you will need to turn the system off. For instance, when having your car serviced, washed or parked by a valet. NOTE: If you temporarily lose the use of your remote controls, you can disarm the system by enabling valet mode. Turn the ignition switch to its "ON" position or start the engine. The system's LED will glow continually for on-going visual confirmation of valet mode. To exit valet mode 1. Turn the ignition switch to its "ON" position or start the engine. The system's LED will turn off to confirm that the system is in its normal operating mode. How to interpret the chirps and parking light flashes When you use the remote control, the system responds with chirps and parking light flashes. These chirp/flash acknowledgments mean: Chirps/flashes 1 2 2 and then 4 3 4 Meaning Your system is disarmed Your system is armed Armed but a door is open or the sensor is malfunctioning (see AutoTesting below) Disarmed but there was an intrusion attempt (see Prior intrusion attempt alert on page 5) Armed but the hood or trunk is ajar (see AutoTesting below) Piezo Sensor The Piezo Sensor that detects intrusion-related vibrations and impacts. AutoTestingTM Each time you remotely arm your ACE 100, it automatically performs an extensive test of all system triggers and sensors. If the hood or trunk is open when you remotely arm, the system will immediately alert you of the problem by sounding 4 chirps and 4 parking light flashes instead of the usual 2 and 2 (simply disarm, shut the hood or trunk and re-arm to reactivate monitoring of that trigger point). If a door is ajar or if a sensor is malfunctioning, you will receive the usual 2 chirps and 2 flashes, then, 5 seconds later, there will be 4 chirps and 4 flashes. (The door ajar warning will not work on vehicles that have factory-delayed courtesy lights). 4 Automatic malfunction bypass The system automatically bypasses any faulty point and arms all other triggers and sensors to provide the utmost protection until you can have the system serviced. Prior intrusion attempt alert If you hear three chirps when you remotely disarm, the alarm sounded in your absence. FACTTM-- False Alarm Control and Test With FACT, you'll never experience repeated false alarms. If the siren goes off, DO NOT remotely disarm the system; allow it to run for the full 30 seconds. Before sounding a second time, the system checks for another activated trigger to verify an intrusion is in progress. [. . . ] To change any of the settings, use the following procedure. To restore the feature to its factory setting, just repeat the procedure: 1. Select the feature you wish to program from the table below. Turn your vehicle's ignition switch to its "ON" position. [. . . ]