User manual CLIFFORD 700IQ

[. . . ] World-Class Auto Security TM intelliguard 700-IQ Owner's Manual All IntelliGuard-IQ Series systems are covered by one or more of the following Clifford Electronics patents: 4, 158, 874; 4, 233, 642; 4, 327, 444; 4, 383, 242; 4, 430, 685; 4, 845, 464; 4, 887, 064; 4, 890, 108; 4, 922, 224; 4, 997, 053; 5, 081, 667; 5, 146, 215; 5, 157, 375 and other patents Table of Contents Standard Features of the IntelliGuard 7OO-IQ . Your 4-button/12-channel remote controls . . . . . . . . . . . . . . . . . 3 8 9 How to use your keychain remote control . 10 How to interpret the chirps and parking light flashes . [. . . ] To enter 31 as your new code, you would press the switch in this manner: momentary, momentary, momentary, latched (you'll hear 3 chirps to confirm the first digit), momentary, latched (1 chirp to confirm the second digit), center. Wait 3 seconds until you hear 2 chirps, indicating the new code has been accepted. Turn off the ignition to exit program mode (you'll hear a 3-chirp confirmation). VERY IMPORTANT: You must immediately test your new secret valet code: Turn on the ignition, enter your new code, then flip the switch to its latched position. If it does not, the new code you programmed and the one you just entered do not match. In such a case, the system will revert to the previous code. Remote controlled valet mode entry and exit You can even enable or exit valet mode with your remote control simply by transmitting channel 9 (LevelShift twice, then button 1). In addition to the above indications, two parking light flashes will confirm that you have remotely enabled valet mode, while a single flash confirms exiting of valet mode. Keyless entry in valet mode Even if valet mode is enabled, you can still remotely control the convenience features. For instance, simply press button 1 (channel 1) as if you were disarming and the doors will unlock (indicated by one parking light flash) and the interior lights will turn on. Press button 1 again and the doors lock (confirmed by two flashes). You can also use the other channels to activate options such as a remote trunk release or remote engine starting. 14 Remote controlled sensor adjustments Due to ever-changing conditions, all alarms require periodic fine-tuning of their sensors. An improperly adjusted sensor is the most common cause of false alarms. With other alarms, this requires repeated trips back to the dealer. You can adjust sensitivity electronically without tools and without even knowing where the sensor is mounted!If the setting(s) of the Piezo Sensor is either too sensitive or not sensitive enough, you may individually test and adjust the settings of each zone. To adjust the Piezo Sensor, just use the following procedure: 1. Disarm the system, then select the sensor zone you wish to adjust: a. Primary zone: Transmit channel 11 (LevelShift twice, then button 3). Warning zone: Transmit channel 12 (LevelShift twice, then button 4). To test the current sensitivity setting: a. Primary zone: Firmly "thump" the window pillar with the side of your fist. You will hear a chirp to confirm activation of the primary zone. [. . . ] To do so, use the "Erase all channels" feature (feature column 2, row 6 on the Table of user-selectable features on pages 23-24). This will clear all remote control codes from the system memory. Then simply program each remaining and/or replacement remote control as noted in the Adding new remote controls section above. 22 Table of user-selectable features: 1 chirp = OFF, two chirps = ON. Feature Select Row 1 1st momentary Row 2 2nd momentary Row 3 3rd momentary Row 4 4th momentary Row 5 5th momentary Row 6 6th momentary Column 1 1st latched Sound 1: on/off info on page 18 Sound 2: on/off info on page 18 Sound 3: on/off info on page 18 Sound 4: on/off info on page 18 Sound 5: on/off info on page 18 Sound 6: on/off info on page 18 Column 2 2nd latched Add new remote to channel 1 info on page 10 NOTE 1 Add new remote to channel 2 info on page 10 NOTE 2 Add new remote to channel 3 info on page 10 NOTE 3 Add new remote to channel 4 info on page 10 NOTE 4 Erase all channels info on page 22 NOTE 5 Headlight Reminder: on/off info on page 16 Column 3 3rd latched AutoLock on/off info on page 16 AutoUnLock on/off info on page 16 FACT: on/off info on page 15 AutoActivate timed accessory upon remote arming: on/off this feature is for installers only QuietChirps: on/off info on page 18 Long-term chirp silencing: on/off info on page 18 Column 4 4th latched AutoArming: on/off info on page 12 AutoArm & Lock: on/off info on page 12 15-second entry delay: on/off info on page 11 D Set headlight duration 1sec - 2min (30sec) info on page 10 NOTE 6 Siren duration: 60/30 seconds (1/2 chirps) info on page 18 Set a new secret valet code info on page 14 NOTE 7 D WARNING: If you have remote window and sunroof closure, DO NOT CHANGE THIS SETTING: it requires installer-only adjustment. Please Note: There is a column 5 that contains installer-only features; do not change any of these settings. [. . . ]