User manual CLIFFORD CONCEPT 470

[. . . ] Concept 470 Owner's Guide limited lifetime consumer warranty Directed Electronics ("Directed") promises to the original purchaser to repair or replace with a comparable reconditioned model any Directed unit (hereafter the "unit"), excluding without limitation the siren, the remote transmitters, the associated sensors and accessories, which proves to be defective in workmanship or material under reasonable use during the lifetime of the vehicle provided the following conditions are met: the unit was professionally installed and serviced by an authorized Directed dealer; the unit will be professionally reinstalled in the vehicle in which it was originally installed by an authorized Directed dealer; and the unit is returned to Directed, shipping prepaid with a legible copy of the bill of sale or other dated proof of purchase bearing the following information: consumer's name, telephone number and address; the authorized dealers name, telephone number and address; complete product description, including accessories; the year, make and model of the vehicle; vehicle license number and vehicle identification number. All components other than the unit, including without limitation the siren, the remote transmitters and the associated sensors and accessories, carry a one-year warranty from the date of purchase of the same. This warranty is non-transferable and is automatically void if: the original purchaser has not completed the warranty card and mailed it within ten (10) days of the date of purchase to the address listed on the card; the unit's date code or serial number is defaced, missing or altered; the unit has been modified or used in a manner contrary to its intended purpose; the unit has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defects in materials or construction. The warranty does not cover damage to the unit caused by installation or removal of the unit. [. . . ] It detects any faulty switches and sensors and prevents them from disabling the entire system. The microprocessor will also record and report any triggers that occurred during your absence. arming diagnostics If the system is armed while an input is active (door open, sensor triggering, etc. ) the unit will chirp twice when arming and then four more times five seconds later. The security system will ignore the input that was active when the system was armed, until the input goes away. Three seconds later the system will monitor that input normally. For example, if your vehicle has interior light exit delay, and you arm the system before the interior light goes out, you may hear Bypass Notification chirps. Once the light shuts off, however, the doors are monitored normally. disarming diagnostics Extra disarm chirps are the Tamper Alert. If three chirps are heard when disarming, the system was triggered in your absence. If three chirps are heard, the LED status indicator will indicate which zone was involved when you turn the ignition on (see the Table of Zones section). The system will retain this information in its memory. Refer to the Multiple Event Total Recall section of this guide. © 2 0 0 6 d i re c t e d e l e c t ro n i c s 15 arm/disarm diagnostic chart Action Arm Arm Chirps 2 4 Light Flashes 2 4 Description System armed System armed with hood/ trunk active and bypassed (zones 5 and 6) System armed with door active and bypassed (zone 4) System armed with sensor active and bypassed zones 1, 3, and 8 System disarmed System disarmed with tamper alert Arm Arm 2 (5 sec. ) 4 2 (10 sec. ) 4 2 (5 sec. ) 4 2 (10 sec. ) 4 Disarm Disarm 1 3 1 3 16 table of zones The zone number is the number of LED flashes used by the system to identify a specific input. The standard input assignments are listed below, along with spaces to write in any optional sensors or switches you have had installed. If the Warning Zone response is triggered, the LED will not report it. Zone - Number of LED Flashes 1 2 3 4 5 6 7 8 9 10 Description Proximity sensor Not used Mux 1 trigger - for optional sensors Door switch trigger Instant trigger - trunk Instant trigger - hood Ignition trigger Mux 2 trigger - for optional sensors Not used Power interrupt Dealer-Installed Options anti-code grabbing (ACG) This unit features Anti-Code Grabbing (ACG) with Random Code Encryption. This means the receiver and transmitters each use a mathematical formula called an algorithm to change their code each time the transmitter is used. This technology has been developed to increase the security of the unit. The control unit knows what the next codes should be. © 2 0 0 6 d i re c t e d e l e c t ro n i c s 17 smart power up II This security system will store its current state to non-volatile memory. If power is lost and then reconnected the system will recall the stored state from memory. This means if the unit is in Valet Mode and the battery is disconnected for any reason, such as servicing the car, when the battery is reconnected the unit will still be in Valet Mode. This applies to all states of the system including arm, disarm, and Valet Mode. power saver mode Your system will automatically enter Power Saver Mode while armed or in Valet Mode, after a period of time in which no operation has been performed. This lowers the current draw on the vehicle's battery and prevents the system from draining the battery. Power Saver Mode takes over under the following conditions: Power Saver when the system is armed: After the system has been armed for 48 hours, the LED will flash at half its normal rate, decreasing the system's current draw. Power Saver in Valet Mode: When the system enters Valet Mode the LED illuminates steadily. If the vehicle is not used (ignition is not turned on) for a period of one hour while the system is in Valet Mode, the LED will shut off. [. . . ] OFF: Valet mode will only be exited by using the valet switch or the remote control. ON: Valet mode will be exited every time the ignition is turned on. mux sensors audio sensor The 506T Audio Sensor is a low-current device that provides an added level of protection to an existing security system by detecting sounds that have the acoustic signature of breaking glass or metal-to-glass impacts. shock sensor The 504C dual zone magnetic resonance shock sensor provides a warn ing trigger for lighter impacts to the vehicle as well as a full trigger for heavy impacts. © 2 0 0 6 d i re c t e d e l e c t ro n i c s 31 health check Directed Electronics recommends you return to your installing Clifford dealer to have your system checked for correct operation. The first check is due one year after the installation date and at yearly intervals thereafter. note: There may be a small charge incurred for this service. 32 glossary of terms Control Unit: The "brain" of your system. Usually hidden underneath the dash area of the vehicle. [. . . ]