User manual CLIFFORD INTELLIGUARD 770

[. . . ] Intelliguard 770 Owner's Guide limited lifetime consumer warranty Directed Electronics ("Directed") promises to the original purchaser to repair or replace with a comparable reconditioned model any Directed unit (hereafter the "unit"), excluding without limitation the siren, the remote transmitters, the associated sensors and accessories, which proves to be defective in workmanship or material under reasonable use during the lifetime of the vehicle provided the following conditions are met: the unit was professionally installed and serviced by an authorized Directed dealer; the unit will be professionally reinstalled in the vehicle in which it was originally installed by an authorized Directed dealer; and the unit is returned to Directed, shipping prepaid with a legible copy of the bill of sale or other dated proof of purchase bearing the following information: consumer's name, telephone number and address; the authorized dealers name, telephone number and address; complete product description, including accessories; the year, make and model of the vehicle; vehicle license number and vehicle identification number. All components other than the unit, including without limitation the siren, the remote transmitters and the associated sensors and accessories, carry a one-year warranty from the date of purchase of the same. This warranty is non-transferable and is automatically void if: the original purchaser has not completed the warranty card and mailed it within ten (10) days of the date of purchase to the address listed on the card; the unit's date code or serial number is defaced, missing or altered; the unit has been modified or used in a manner contrary to its intended purpose; the unit has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defects in materials or construction. The warranty does not cover damage to the unit caused by installation or removal of the unit. [. . . ] This applies to all states of the system including arm, disarm, and Valet® Mode. power saver mode Your system will automatically enter Power Saver Mode while armed or in Valet® Mode, after a period of time in which no operation has been performed. This lowers the current draw on the vehicle's battery and prevents the system from draining the battery. Power Saver Mode takes over under the following conditions: © 2 0 0 6 d i re c t e d e l e c t ro n i c s 19 Power Saver when the system is armed: After the system has been armed for 48 hours, the LED will flash at half its normal rate, decreasing the system's current draw. Power Saver in Valet® Mode: When the system enters Valet® Mode the LED illuminates steadily. If the vehicle is not used (ignition is not turned on) for a period of one hour while the system is in Valet® Mode, the LED will shut off. If the system remains in Valet® Mode, the LED will come back on the next time the ignition is turned on and then back off. programming options Programming options control what your system does during normal operation, and require few or no additional parts. However, some may require additional installation labor. Following is a list of the program settings, with the factory settings in bold: Active arming (only with the remote) or passive arming (automatic arming 30-seconds after the last door is closed). Arming/disarming confirmation siren chirps on or off. ON: The doors will lock three seconds after the ignition is turned on unless a door is open. RPM: The doors will lock when the engine speed increases. Auto-Unlock on/off: With this feature on, the doors will unlock when the ignition is turned off. Passive door locking (with passive arming) or active door locking (only when arming with the remote). Passive locking 20 allows the vehicle's doors to lock when the security system passively arms (after the 30 second countdown). This feature only works if passive arming has been programmed. Panic mode enabled/disabled: Some states have laws against siren capability while driving. Full trigger response 30, 60, or 90 seconds: This determines how long the full triggered sequence lasts. Some states have laws regulating how long a security system can sound before it is considered a nuisance. False Alarm Control Technology (FACT II) on or off: Please refer to the FACT II section of this guide for a complete explanation of how FACT II operates. If FACT II is programmed off, the security system will respond to inputs from any sensor indefinitely. note: Because many states have laws regulating security systems, programming FACT II off may cause your system to violate state laws. Siren tones and chirp volume: The output of the siren consists of six different tones in sequence and the arm/disarm chirp volume can be changed or eliminated. Reset the system to all factory defaults. Autostart with low battery voltage or cold temperature. © 2 0 0 6 d i re c t e d e l e c t ro n i c s 21 cliffnet wizard installation software programming Cliffnet Wizard provides access to all available system features and some that are not available when manually programming with the Valet® button. [. . . ] to re-enter Primary zone adjustment Siren chirps 2 times. 38 Primary zone can now be re-adjusted as described in step 4. Or press again to exit programming mode. The siren will chirp 3 times when sensor adjustment mode has been exited. note: You must wait 15-seconds for the Omnisensor to become active after arming. glossary of terms Control Unit: The "brain" of your system. Usually hidden underneath the dash area of the vehicle. [. . . ]