User manual CLIFFORD SOLARIS 5

[. . . ] Solaris 5 Owner's Guide limited lifetime consumer warranty Directed Electronics, Inc. ("Directed") promises to the original purchaser to repair or replace with a comparable reconditioned model any Directed unit (hereafter the "unit"), excluding without limitation the siren, the remote transmitters, the associated sensors and accessories, which proves to be defective in workmanship or material under reasonable use during the lifetime of the vehicle provided the following conditions are met: the unit was professionally installed and serviced by an authorized Directed dealer; the unit will be professionally reinstalled in the vehicle in which it was originally installed by an authorized Directed dealer; and the unit is returned to Directed, shipping prepaid with a legible copy of the bill of sale or other dated proof of purchase bearing the following information: consumer's name, telephone number and address; the authorized dealers name, telephone number and address; complete product description, including accessories; the year, make and model of the vehicle; vehicle license number and vehicle identification number. All components other than the unit, including without limitation the siren, the remote transmitters and the associated sensors and accessories, carry a one-year warranty from the date of purchase of the same. This warranty is non-transferable and is automatically void if: the original purchaser has not completed the warranty card and mailed it within ten (10) days of the date of purchase to the address listed on the card; the unit's date code or serial number is defaced, missing or altered; the unit has been modified or used in a manner contrary to its intended purpose; the unit has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defects in materials or construction. [. . . ] To enter the User Selectable Features programming: 1. Ignition on - Turn the ignition to the run position or start the engine. Enter PIN - Enter the factory preset PIN code 2 by pressing on the PlainView 2 Valet switch twice, then once. note: If the factory preset PIN has been changed, the new PIN must be entered. © 2 0 0 3 d i re c t e d e l e c t ro n i c s , i n c . 21 3. Hold/Chirp/Release - After entering the PIN code, press and hold until a chirp is heard and the LED turns on, then release the button. You have now entered the feature selection position of the User Selectable Features grid. Column select - Press the same number of times as the desired column. After a pause the siren will chirp the same number of times as the selected column for confirmation. Feature select - Press the same number of times as the desired feature. The feature can now be changed using the remote control. Feature change - Press on the transmitter. If the system chirps once, the feature has just turned off; if the system chips twice, the feature has just turned on. If the feature has more than two settings, continue pressing on the transmitter to toggle through the settings. You can advance to any feature in the same column by pressing within 60 seconds; to program a feature in a different column begin at step 4 within 60 seconds. note: Refer to the Feature Descriptions sections of this guide for important notes and descriptions of the system features and programming. 4. 5. 6. 7. Exit programming - To exit programming mode turn the ignition off or wait 60 seconds without pressing the PlainView 2 Valet switch. The siren will chirp three times to indicate programming mode has been exited. 22 user selectable features Then Press First Press Add new remote (autolearn) Auto (passive) arm on/off Chirps on/off/quiet Auto lock ignition/off/rpm Auto unlock ignition/off Auto (passive) arm and lock on/off Siren duration 30/60/90 Second unlock on/off Not used Set PIN code (default = 2) Select siren sounds FACT II on/off Remote valet on/off Entry delay on/off Reset to default (except transmitter and valet code) Panic on/off Autostart setting* (off/battery only/ temp only/ battery and temp) Not used New remote learn arm/disarm only New remote learn accessory A channel New remote learn accessory B channel New remote learn silent mode New remote learn remote valet New remote learn remote start* New remote learn window down/vent** Not used Clear all remotes * This feature is only available with optional IntelliStart connected. ** This feature is only available with optional SmartWindows connected. © 2 0 0 3 d i re c t e d e l e c t ro n i c s , i n c . 23 user selectable features descriptions - column one add new remote (auto learn) Auto-learn new five-button Radar2 remote controls to the system in the standard button configuration. Once you have entered the feature, press learned. auto (passive) arm - on/off On: When the system sees the ignition turn off and the last protected entry (door, hood, or trunk) close, it will begin a 30-second countdown before arming itself. After the first five seconds, you will hear two chirps and the lights will flash. Off: The transmitter must be used to arm the system. chirps - on/off/quiet On: Chirps will sound when arming/disarming the system. Off: Chirps will not sound when arming/disarming the system. Quiet: Chirps will sound when arming/disarming the system but at a lower volume than normal. auto lock - ignition/off/rpm Ignition: The doors will automatically lock three seconds after the ignition is turned on unless a door is open at that time. [. . . ] Siren chirps 2 times Primary zone can now be re-adjusted as described in step 3. Or press again to lock in primary zone setting and exit programming mode. The siren will chirp 3 times when sensor adjustment mode has been exited. © 2 0 0 3 d i re c t e d e l e c t ro n i c s , i n c . 39 Auto-Scroll for adjusting sensitivity - press and hold or to increase or decrease sensitivity setting several levels rapidly. 40 glossary of terms Control Unit: The "brain" of your system. Usually hidden underneath the dash area of the vehicle. [. . . ]