User manual CLIFFORD XL 4000

[. . . ] World-Class Auto Security TM All XL Series systems are covered by one or more of the following Clifford Electronics patents: 4, 158, 874; 4, 233, 642; 4, 327, 444; 4, 383, 242; 4, 430, 685; 4, 845, 464; 4, 887, 064; 4, 890, 108; 4, 922, 224; 4, 997, 053; 5, 081, 667; 5, 146, 215; 5, 157, 375 and other patents Table of Contents Standard Features of the XL4000 Welcome . . . . . . . . . . . . . . . . . . . 9 Your 4-button/12-channel remote controls . 10 How to use your keychain remote control . 11 How to interpret the chirps and parking light flashes . [. . . ] From the Table of user-selectable features on pages 23 and 24, you would note that the "set a new secret valet code" feature is in column 3, row 5. Enter program mode by turning on the ignition, entering your current valet code, then pressing the PlainView switch to its momentary side for 3 seconds until you hear a chirp. Select column 3 by moving the switch between latched and center 3 times, i. e. : latched, center, latched, center, latched, center. After a brief pause, you will hear 3 chirps to confirm that you have selected feature column 3. Select row 5 by pressing and releasing the momentary side of the switch 5 times. To help you count, you will hear a chirp each time you press the momentary side. Immediately flip the switch to the latched position. To enter 31 as your new code, you would press the switch in this manner: momentary, momentary, momentary, latched (you'll hear 3 chirps to confirm the first digit), momentary, latched (1 chirp to confirm the second digit), center. Wait 3 seconds until you hear 2 chirps, indicating the new code has been accepted. Turn off the ignition to exit program mode (you'll hear a 3-chirp confirmation). VERY IMPORTANT: You must immediately test your new secret valet code: Turn on the ignition, enter your new code, then flip the switch to its latched position. If it does not, the new code you programmed and the one you just entered do not match. In such a case, the system will revert to the previous code. Remote controlled valet mode entry and exit You can even enable or exit valet mode with your remote control simply by transmitting channel 9 (LevelShift twice, then button 1). In addition to the above indications, two parking light flashes will confirm that you have remotely enabled valet mode, while a single flash confirms exiting of valet mode. Keyless entry in valet mode Even if valet mode is enabled, you can still remotely control the convenience features. For instance, simply press button 1 (channel 1) as if you were disarming and the doors will unlock (indicated by one parking light flash) and the interior lights will turn on. Press button 1 again and the doors lock (confirmed by two flashes). You can also use the other channels to activate options such as a remote trunk release or remote engine starting. 15 FACTTM-- False Alarm Control and Test With FACT, you'll never experience repeated false alarms. If the Insignia Siren goes off, DO NOT remotely disarm the system; allow it to run for the full siren duration. Before sounding the siren a second time, the system automatically checks for another activated trigger to verify that an intrusion is in progress. Should the siren sound again, you will know for sure that someone is tampering with your vehicle. (To disable FACT, see User-selectable features on pages 20-24. ) Selectable starter/ignition interrupt At the time of installation, you can select whether your XL4000 interrupts the starter line or the ignition line. [. . . ] This will clear all remote control codes from the system memory. Then simply program each remaining and/or replacement remote control as noted in the Adding new remote controls section above. 22 Table of user-selectable features: 1 chirp = OFF, two chirps = ON. Feature Select Row 1 1st momentary Add new remote to channel 1 info on page 11 NOTE 1 Add new remote to channel 2 info on page 11 NOTE 2 Add new remote to channel 3 info on page 11 NOTE 3 Add new remote to channel 4 info on page 11 NOTE 4 Erase all channels info on page 22 NOTE 5 AutoUnLock on/off info on page 16 FACT: on/off info on page 16 AutoActivate timed accessory upon remote arming: on/off THIS FEATURE IS FOR INSTALLERS ONLY Long-term chirp silencing: on/off info on page 19 AutoLock on/off info on page 16 Column 1 1st latched Column 2 2nd latched Column 3 3rd latched Enhanced AutoArming: on/off info on page 13 Row 2 2nd momentary Row 3 3rd momentary Row 4 4th momentary Row 5 5th momentary AutoArm & Lock: on/off info on page 13 D Set headlight duration: 1sec - 2. 5min (30sec) info on page 12 NOTE 6 Siren duration: 60/30 seconds (1/2 chirps) info on page 19 Set a new secret valet code info on page 15 NOTE 7 D WARNING: If you have remote window and sunroof closure, DO NOT CHANGE THIS SETTING: it requires installer-only adjustment. Please Note: There is a column 4 that contains installer-only features; do not change any of these settings. If you accidentally select column 4, turn off the ignition. NOTE 1: Transmit channel 1 (or other channel of your choosing) of the new remote control. [. . . ]