User manual COBRA CP9125ML

[. . . ] CP9125manual(6. 12) 10/20/98 11:38 AM Page 1 CP-9125 Cobra Electronics Corporation 6500 West Cortland Street Chicago, IL60707 FCC Information FCC Information Included Accessories 1 Registered with The FCC Please note: This cordless phone operates under part 15 and part 68 of FCC rules. Operation is subject to two conditions: 1. It may not interfere with radio communications, and 2. It must accept any interference received, including that which may cause undesirable operation. See the Operational Features section of this manual for ways to reduce interference. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Operating Instructions for your Cobra CP-9125 If You Think You Need Service For technical assistance, please call our Automated Help Desk which can assist you by answering the most frequently asked questions about Cobra products. Private Call 900 ® 2 (773) 889-3087 24 hours a day, 7 days a week. [. . . ] If you would like to try again in a few minutes, push and release TALK button for dial tone, then: handset or base Last Number Delayed Redial 1 2 Push and release FLASH button. Listen for dial tone. 3 4 Push and release REDIAL/PAUSE button. The number will be redialed. 3 4 Push and release REDIAL/PAUSE button. 21 20 CP9125manual(6. 12) 10/20/98 11:38 AM Page 28 Operation Memory Number Storage Memory Number Storage The CP-9125 will store up to 10 frequently called numbers. Operation Note To store numbers from the base follow the same proceedure used for the handset. Memory 3 Push and release button again. There will be 2 double beeps. Note 1. You may also use the button in memory to temporarily change from pulse to tone dialing. 1 Push and release Memory button once. * 2. The REDIAL/PAUSE button in memory enters a 3 second delay. Note 4 Assign memory position by en tering keypad number from 0 to 9. There will be two quick double beeps to confirm number storage. Repeat for additional numbers to be stored in memory. Enter name beside MEMORY number on the memory label provided with the unit. 2 Enter digits of number to be stored (up to 16). 22 23 CP9125manual(6. 12) 10/20/98 11:38 AM Page 30 Operation Memory Number Dialing Memory Number Dialing 1 Operation To Find The Handset The handset can be located when it's away from the base. To locate the handset: Access the line. To Find The Handset Note Memory dialing from base uses same procedure as handset. Memory 2 Push and release button once. Intercom Page/Find 1 Push and release button. The handset will beep for 30 seconds, allowing time to locate the handset. 3 Pushand release keypad number, (0-9), you assigned for that phone number. The phone will dial that number automatically. 2 If you wish to stop beep tones push and release Talk or buttons , wait 2 seconds, push and release again or, push and release button on base. Int/Page Intercom Page/Find 24 25 CP9125manual(6. 12) 10/20/98 11:38 AM Page 32 Operation Intercom Mode From The Handset Intercom Mode From The Handset Your CP-9125 can serve as an intercom between the base and the handset. To utilize this feature: Operation Intercom Mode The From Base Intercom Mode From The Base Note Intercom may be initiated from either the handset or the base. Intercom Page/Find Note To initiate INTERCOM while on Hold a call, push and release button. Then push and release Intercom Page/Find button. Proceed following INTERCOM instructions. Note Only the handset can end INTERCOM mode. Push and release Int/Page button to end. 1 1 Push and release will illuminate. Int/Page button. The Intercom LED Low Batt Push and release button. The will flash on the base. In Use LED Low Batt 2 The and LED will light on the base. Begin talking. In Use Intercom 2 The Intercom LED will flash and the handset will beep. 3 26 27 CP9125manual(6. 12) 10/20/98 11:38 AM Page 34 Operation Intercom Mode From The Base continued Hold Button On The Base Operation Hold Button On The Base Note Hold 1 3 The person using the handset should push and release the button. Int/Page Push and release button to put a par ty on hold or to prevent them from hearing you. The Speakerphone LED on base will blink. To release HOLD push and release the button or pick up a branch phone , which will automatically disconnect the CP-9125. Speakerphone When party is on hold, the LED will be illuminated on the base. In Use 2 4 Begin talking. Hold Button On The Handset Hold Button On The Handset Hold 1 Push and release button to put a par ty on hold or to prevent them from hearing you. The In Use LED on the handset will blink. To release HOLD push and release Talk button or pick up a branch phone, which will automatically disconnect the CP-9125. 29 2 28 CP9125manual(6. 12) 10/20/98 11:38 AM Page 36 Operation Ringer Switch Ringer Switch OFF/ON switch (on base) controls the handset ringer. Operation Handset Battery Recharging When the handset battery needs recharging: Handset Battery Recharging Note When ringer switch is off you can detect an incoming call by the flashing IN USE LED on the handset or on the base. Note Replacement batteries are available from Cobra. [. . . ] If the noise disappears, then it is most lik ely local interference being generated by a source outside your home, or a source inside your home strong enough to blanket your entire house such as a baby monitor. If you find that the noise and interference are equally strong throughout your house, your cordless phone may require service. 41 Cobra Customer Service Live operators are available M-F 8:00 am - 8:00 pm CST at: 773. 889. 3087 Automated Technical Assistance available 24 hours a day, seven days a week. E-mail questions to: productinfo@cobraelec. com Cobra on the World Wide Web: Frequently Asked Questions (FAQ) can be found on-line at: www. cobraelec. com 40 CP9125manual(6. 12) 10/20/98 11:39 AM Page 48 Frequently Asked Questions 6. Will more than one cordless phone work in the house? [. . . ]