User manual COBRA CPI 480 QUICK START GUIDE

[. . . ] Introduction Our Thanks to You Our Thanks CPI 480 Thank you for purchasing the Cobra to You inverter. Properly used, this Cobra product will give you many years of reliable service. Operating Instructions How Your Cobra Power Inverter Works The Cobra power inverter is an electronic product that has been designed and built to take low voltage DC (Direct Current) power from your automobile or other low voltage power supplies and convert it to standard 115 Volt AC (Alternating Current) power like the current you have in your home. This conversion process thereby allows you to use many of your household appliances and electronic products in automobiles, RVs, boats, tractors, trucks and virtually anywhere else. The Cobra line of quality products includes: Customer Assistance CB Radios microTALK® Radios Radar/Laser Detectors Safety Alert® Traffic Warning Systems Mobile GPS Navigation Systems HighGear® Accessories CobraMarine® VHF Radios CobraMarine® Chartplotters Power Inverters Accessories Customer Assistance Should you encounter any problems with this product, or not understand its many features, please refer to this owner's manual. If you require further assistance after reading this manual, Cobra Electronics offers the following customer assistance services: For Assistance in the U. S. A. [. . . ] WARNING This unit contains components which can produce arcs or sparks. To prevent fire or explosion, do not install in compartments containing a battery or flammable materials, or in a location which requires ignition protected equipment. Connect Test Load The inverter should supply power to the load. If the inverter is not working properly, refer to the troubleshooting guide on page 14 or power and protection indicators section on page 12. USB Connection 4 Nothing Comes Close to a Cobra® 5 Installation Mounting and Connecting Cables · Installation Connecting Cables Mounting To mount your inverter: 1. Place the inverter on a flat surface with the mounting bracket against the mounting surface. Mounting Brackets 2. Connect cable to the Power Input Terminals on right side panel of the inverter. The red terminal is positive (+) and the black terminal is negative (-). Insert the ends of the cables onto the terminals and tighten the screws to clamp the cables safely. Connect Terminals 2. Connect the cable from the Positive (Red) Terminal of the inverter to the Positive Terminal of the power source (the battery's main fuse or the battery selector switch, if you are using one). You might observe a spark when you make this connection since current can flow to charge capacitors in the inverter. All power connections to your Cobra inverter must be Positive to Positive and Negative to Negative. Connect Power Source CAUTION Do not connect the inverter and another AC source (such as a generator or utility power) to the AC wiring at the same time. The inverter will be damaged if its output is connected to AC voltage from another source. Damage can even occur if the inverter is switched off. CAUTION Do not connect the inverter to an AC branch circuit that has high-power consumption loads. It will not operate electric heaters, air conditioners, stoves, and other electrical appliances that consume more than 400 watts. CAUTION Loose connectors result in excessive voltage drop and may cause over heated wires and melted insulation. CAUTION Reverse polarity connections (positive to negative) will blow external fuse in the inverter and may permanently damage the unit. Such damage is not covered by the warranty. CAUTION Remove any jewelry (watch, ring, etc. ). Be careful not to short circuit the battery with any metallic object (wrench, etc. ). WARNING 115 volt AC power is potentially lethal. Do not work on AC wiring when it is connected to the inverter (even if it is switched off) unless the DC power source is physically disconnected from the inverter. Also, do not work on AC wiring if it is connected to another AC power source such as a generator or the utility line. [. . . ] 800W Peak efficiency (12V ­ 1/2 load) . < 0. 5A (12. 6V) Output waveform (resistive load) . 10. 4VDC ­ 14. 4VDC Alarm voltage (unload) . . 10. 2V ­ 10. 8V Shutdown voltage (unload) . [. . . ]