User manual COBRA REMOTE-CARD

[. . . ] · The buzzer will issue two beeps (if activated). · The protections activate after a 40 s timer has elapsed. · The LED will come on constantly for 40 s then it will flash. 3. 6 - Deactivating the volumetric ultrasonic sensor The volumetric sensor can be deactivated if you want to leave the windows open or if someone remains in the passenger compartment. 1) Press the button on the emergency panel within 5 s after having switched off the ignition key. [. . . ] The sensor has been inhibited; all other functions remain activated. Sensors will automatically armed again when the ignition key will be switched on. 3. 2 - Protection When armed the system will generate an acoustic and visual 30 s alarm when the bonnet, boot or one of the doors is opened. System with the volumetric sensor will generate the alarm in case of intrusion. The system remains armed at the end of the cycle. 3. 3 - Interrupting an alarm cycle When sounding, disarm the system (see point 3. 4). 3. 7 - Garage function The `garage' function allows you to temporarily exclude passive arming and anti-hi-jack functions. This can be useful when you have to take the car for service interval without having to leave the radio control. IMPORTANT: never leave radio control key and PIN code together with car keys. Before you leave the car, proceed as follows: switch ON the ignition, open a door and digit the PIN code by using the emergency button. Confirmation of the function activation is given by a single blink of the turn indicators. This function is automatically deactivated when the system is armed and disarmed by the radio control or the ignition key is switched ON and OFF for 10 times. 3. 4 - Disarming · · · · · Press the button on the radio control to open the doors. The buzzer will issue one beep (if activated). The protection are deactivated immediately. Note: This working mode is available only for non EC products model. 27 REMOTE-CARD 5 - ADVANCED FUNCTIONS 17/01/2005, 14. 40 6 - ALARM MEMORY If an alarm trigger has occurred the buzzer and the turn indicators will give four signals. The alarm status history is displayed by LED when the system is disarmed, this is played until the ignition is switched ON. L E D S IG N A L 1 blink 2 blinks 3 blinks 4 blinks 5 blinks 6 blinks A L A R M D E S C R IP T IO N doors, boot have been opened ultrasonic volumetric sensor triggered bonnet has been opened attemps to start (ignition key/hotwire) movement sensor input/alarm tamper mode 28 6 - ALARM MEMORY REMOTE-CARD 06DE2085A. pmd 17 7 - EMERGENCY OVERRIDE To deactivate the system without a radio control proceed as follows: Push the button of the emergency panel the number of times corresponding to the first digit of your PIN code. The LED will blink everytime you press the button, a longer blink will confirm that the right PIN code digit has been input. Proceed in the same way with the 3 further digits. The system will disarm as soon as the last digit is input. Push for a number of times correspondent to the digit of your PIN code SIREN ON quick flashing PIN CODE OK ALARM DISARMED pause long flashing Enter following digit of your PIN CODE 29 REMOTE-CARD 7 - EMERGENCY 17/01/2005, 14. 40 EMERGENCY 8 - PERSONAL PIN CODE The PIN code should be personalized. The system is delivered with the code 1111 and it must be replaced by a four digits code without the number `0'. To program the system with your own four digit PIN code, disarm the system then proceed as follows: · open a door. · push the button on the emergency panel for a number of times corresponding to the first digit of the old PIN code. The LED will blink everytime you press the button, a longer blink will confirm that the right PIN code digit has been input. Proceed in the same way for all others digits. When the code is recognized the turn indicators will blink once. [. . . ] When it goes off you can digit the new PIN code. · press the button on the emergency panel for a number of times corresponding to the first digit of the new PIN code. The LED will blink everytime you press the button, a longer blink will confirm that the right PIN code digit has been input. · repeat the new code entry: press the button on the emergency panel for a number of times corresponding to the first digit of the new PIN code. [. . . ]