User manual COBRA XRS 9740 QUICK START GUIDE

[. . . ] Introduction Intro Important Information and Customer Assistance Operation Customer Warranty Assistance Important Information 12 Operating Instructions Federal Laws Governing the Use of Radar Detectors It is not against federal law to receive radar transmissions with your Cobra radar/ laser detector. The Communications Act of 1924 guarantees your right to receive radio Secondary Icons transmissions on any frequency. Local laws that contravene this Act, while illegal, may be enforced by your local law enforcement officials until and unless they are prohibited from doing so by federal court action. Safety Alert Use of this product is not intended to, and does not, ensure that motorists or passengers will not be involved in traffic accidents. [. . . ] The compass temporarily may not provide accurate readings if you are inside a building or enclosure, or are close to a large metal tractor/trailer, truck, or train. Once you are away from such a location, the compass will work correctly again. NOTE When the instructions direct you to drive in two circles, a large parking lot is the most convenient place to do so. It does not matter what direction your vehicle is pointing when you start the circles, which direction you go to make the circles, and it does not have to be exactly two circles. You do NOT have to make perfect circles. You can drive in any pattern, as long as you make two complete turns. Four three-point turns, two small squares, or any two complete loops will work as well as two circles. It does not matter what size the circles are, if your speed is constant, or how fast you make the circles [but less than two minutes]. Please be careful when making the circles and watch for other traffic. Nothing Comes Close to a Cobra® 17 Secondary Icons ondary Icons Setting IntelliMute RRMs Set Intel. . . Intelli Mute Set! Notice NOTE If the unit is unable to sense usable pulses within three seconds or if you do not set a rev point within 20 seconds of beginning these steps, IntelliMute will indicate an error and automatically turn off. IntelliMute Not Set Notice IntelliMute Off Intelli Tone One beep One beep 16 English Visual Display IntelliMute not set Please try again IntelliMute Off Voice IntelliMu. . . IntelliMute not set Please try again IntelliMute Off Mute Please tr. . . Off Your Detector Intro Operation Settings Customer Assistance Warranty Your Detector Settings Customer Assistance Warranty Set/City Button Select/Dim Button Pop Alert Intro Operation Pop Alert will alert you of Pop radar signals. During the alert, the unit continues to detect other signals. The factory setting is Pop Detect off. Secondary Icons Program/Mute Button Secondary Icons To Turn Pop Detect Mode On or Off Using Program Mode (See Page 7 For Instructions on Using Program Mode) To Calibrate the Compass Using Program Mode (See Page 7 For Instructions on Using Program Mode) In Program mode, go to Set Compass. Press and release the Set/City button to begin setting the compass. Notice Tone None One (1) beep Visual Display Voice Set Compass None In Program mode, go to Pop Detect. Tone Two beeps One beep Visual Display Pop On Pop Off Pop Detect Off Voice Pop On Pop Off Drive in 2 Set Compass circles. . . Compass Set For two seconds followed by direction of travel (N, NE, E, SE, S, SW, W or NW) None None Notice Pop Detect On Pop On Pop Off Within two minutes, drive your vehicle in a circle twice, then press the Set/City button again. Three beeps K, Ku and X Band Detection The new Ku Band may be introduced to North America in the future. To prevent false alerts until it is, the factory default for Ku Band detection is off. In parts of North America, annoying false alerts from door openers and similar devices are triggered on the X Band and K Band. If desired, X Band or K Band can be turned off. The factory default for X Band and K Band detection is on. To Turn X, K and/or Ku Mode On or Off Using Program Mode (See Page 7 For Instructions on Using Program Mode) n Icons Intro Press and release either the Select/Dim None button to proceed to the next user Operation Customer Warranty mode or the Program/Mute button Assistance to exit Program mode. Set Compass Calibrate Compass Drive in. . . Press SET. . . In Program mode, go to X, K or Ku band. Compass Set Compass Set! Tone Two beeps One beep Two beeps One beep Visual Display X-Band On X-Band Off K-Band On K-Band Off Ku-Band On Ku-Band Off Ku-Band On Voice X On X Off K On K Off Ku On Ku Off Ku-Band Off Direction of Travel X-Band On NW h ondary Icons Set Compa. . . X-Band On Notice NOTE If you do not press the Set/City button within two minutes after beginning the set compass process, compass calibration will automatically terminate. Visual Display Voice Terminate X-Band Off Two beeps X-Band Off One beep K-Band On K-Band Off Tone One beep Compass not set. . . [. . . ] See customer assistance on page A1. y Icons · Trademark Acknowledgement Cobra®, DigiView®, EasySet®, Extra Sensory Detection®, IntelliMute®, IntelliShield®, LaserEye®, Nothing Comes Close to a Cobra®, Safety Alert® Traffic Warning System, Strobe Alert®, VG-2 Alert®, Xtreme Range Superheterodyne® and the snake design are registered trademarks of Cobra Electronics Corporation, USA. Cobra Electronics CorporationTM, 12 BandTM, ExtremeBright DataGrafixTM, IntelliLinkTM, RevolutionTM Series, SmartPowerTM, Spectre AlertTM, SuperXtreme Range SuperheterodyneTM, S-XRSTM, UltraBrightTM, and Voice AlertTM Notice are trademarks of Cobra Electronics Corporation, USA. · Secondary Icons If this product should require factory service, please call Cobra first at 773-889-3087 BEFORE sending the product. This will ensure the fastest turnaround time on any repair. If Cobra asks that the product be sent to its factory, the following must be Notice furnished to have the product serviced and returned: 1. [. . . ]