User manual COEF MP 150 SPOT DV

[. . . ] 150 sp ot http://www. coef. it e-mail:info@coef. it 150 Code ZL-013001-01 OPERATING INSTRUCTIONS Revision 2. 0 SUMMARY DECLARATION OF CE CONFORMITY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 ADVICES FOR A CORRECT INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 GENERAL WARRANTY CONDITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 PACKING CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The guarantee is not valid in case of tampering or repairs carried out by non-authorized personnel. The replacement of the equipment during the validity of the guarantee is not provided for. The transport freights from and to the manufacturer for repairs under guarantee are at Customer's charge. When applying for the repair, always mention the serial number and the model of the equipment. PACKING CONTENTS Carefully check the contents of the packaging and the completeness of the components. If any of the parts listed hereunder is missing, please contact your Dealer immediately: · · · · · · · Complet MP150 Spot DV unit This user manual 1 cable with 1 XLR 3 pin male and 1 XLR 3 pin female 1 AC Power cord 1 safety-chain equipped with two snaps. 1 complete bracket for the ceiling fixing 1 bee M10 PROTECT NATURE. DO NOT DISPOSE OF THE PACKAGING IN THE ENVIRONMENT. CAREFULLY KEEP THE BOX AND THE COMPONENTS OF THE PACKAGING FOR ANY DISPLACEMENT OR RE-SHIPMENT OF THE EQUIPMENT. Do not leave the packaging elements (polystyrene, nylon, metal parts, etc. ) unattended; they might be dangerous for children. Pag. 3 1. 0 DIMENSIONS & POSITIONING It is possible to set up the MP150 Spot DV in any position. 2. 0 TECHNICAL NOTES MP150 Spot DV Code: ZL-013001-01 · · · · · · · · · · · · · · · · · · Lamp: HSD 150/70 -12. 000 lumen 16 bit movement resolution -PAN 540° / TILT 270°with automatic repositioning Optical system with 3 lenses + dichroic reflector 11 colors + white + bi-colors 5 rotating metal gobos all interchangeable+2dichroic gobo Adjustable strobe Rainbow effect adjustable in speed Focus adjustable Black light filter Shutter motorized Multifunction display Remote reset via DMX Remote On/Off lamp via DMX Software upgrade via DMX (with UNI-PROG 8 Accessory) Automatic fault survey Internal power factor correction DMX 512 standard Weight:13Kg Power supply | Absorbed power Volts 230V~ Hz 50Hz I 0, 9A. W 210W Pag. 4 3. 0 INSTALLATION The constructor is not be considered responsible in case of: · · · · · · · · · Improper use of the unit or use by not trained staff Use in contrast with the directions on work safety Wrong installation Defective power supply Serious lacks in the necessary maintenance Unauthorized modifications and interventions Use of spare parts that are not original or not specific for the unit Total or partial inobservance of instructions Unusual events 3. 1 LAMP MOUNTING OR REPLACING WARNING: read carefully · · · · · · · · Switch off the projector before operating. The lamp used in the fixture is a high pressure lamp and must be handled very carefully. The unit is realized to use only HSD 150/70 or compatible lamps; absolutely don't use other types of lamp. The lamp must be changed if damaged or deformed by heat. Wait at least 15 minutes after the projector has been switched off before operating again, in order to let it cool down and avoid the lamp explosion. Read carefully the lamp builder's instructions. Don't look directly the lamp. Wait 30 minutes in order to avoid burns. Unscrew with a cross screwdriver the 4 screw A and to remove the cover that supports the lampholder. Insert delicately the lamp in the projector support, driving it with the cover. Pay attention: the lampholder's wires must correctly reenter in the projector. Block the cover screwing the screws up ( part. A). Pag. 5 3. 2 PROJECTOR INSTALLATION To fix the MP150 Spot DV is necessary, when the installation has to be on a raised-from-the ground support, to block the quick lock/release brackets of the unit by means of a screw provided with nut and locknut measuring not less than M10X50, to insert in the central pre-arranged hole on the fixing bracket. In addiction to the provided quick lock/release (omega) brackets, in order to guarantee a necessary security and in respect of the actual safetyrules concerning the projectors' installation, it is compulsory to install a safetychain, equipped with two snaps, provided with the projector, to connect the MP150 Spot DV 's body to the fixing structure. [. . . ] The lamp is pre-regulated by the factory. Don't move the screws "B" up to upper or lower extremities. Lamp adjustment is necessary to obtain a uniform and powerful light beam. Switch on the projector and set the channels without gobo and colors. Adjust the three screws B until you reach the ideal condition between power and homogeneity. 9. 0 ORDINARY MAINTENANCE Ordinary maintenance on the projectors MP150 Spot DV is necessary to maintain the perfect efficiency of the unit and to avoid defects like the low luminosity of the light beam or the elevated overheating of the equipment. [. . . ]