User manual COLEMAN 9943-780

[. . . ] LOOK INSIDE FOR: Easy Assembly Instructions Repair Parts List Safety, Maintenance and Cleaning Tips ASSEMBLY INSTRUCTIONS FOR 9943 SERIES GAS BARBECUE GRILL ASSEMBLER/INSTALLER: LEAVE THESE INSTRUCTIONS WITH THE CONSUMER. READ ALL THESE INSTRUCTIONS AND KEEP THEM IN A SAFE PLACE FOR FUTURE REFERENCE. CONSUMER/USER: LP Tank Sold Separately 9-Volt Battery Included WARNING: THE EDGES OF SHEET METAL PARTS CAN CAUSE INJURY IF NOT HANDLED WITH CARE. USE EXTREME CAUTION! IMPORTANT! ENSURE PROPER GAS FLOW, BURNER CONTROL VALVES MUST BE "OFF" BEFORE OPENING THE GAS CYLINDER VALVE. TO WARNING Combustion by-products produced when using this product contain chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. 9943-054 (04/26/02) Coleman Company, Inc. Hydraulic Wichita, KS 67219 Internet site: www. coleman. com 1-800-356-3612 TDD: 316-832-8707 (Pg. 2) TORX BIT SOCKET INCLUDED #T-20, 3/8" Square Drive Torx Bit Socket ADDITIONAL TOOLS NEEDED: #2 Phillips Screwdriver 3/8", 7/16" and 11/16" Open End Wrenchs 3/8" Square Drive Ratchet Wrench 3/8" Square Drive Extension OPTIONAL TOOLS: Electric or Cordless Screwdriver #2 Phillips driver bit #T-20 6-Lobe Screwdriver Assemble the Electrode to the Left Burner Casting per illustration (1-A). [. . . ] Fasten wheels tight against the Base Casting. Use an 11/16" open end wrench to tighten the Hex Collar against the Base Casting. (Pg. 14) Step 12 NOTE: Use a ground cloth to protect the paint finish during this step. Check that all fasteners are tightened before turning the grill Right-Side-Up. Carefully turn the grill Right-Side-Up. 12-A Protect with groundcloth Control Panel this side. Protect with groundcloth Complete Assembly of the Console to the Pedestal. Step 13 EY 13-A View of Inside of Main Burner 13-A. Assemble four HEX NUTS (EY) onto the four studs that protrude through the center burner casting. Tighten all fasteners. Hardware shown actual size (EY) #10-24 Hex Nut (4) Qty. (Pg. 16) Step 14 Assemble the BURNER to the RIGHT CONSOLE. Slip BURNER TUBE through RIGHT CONSOLE per detail 14-A. Align BURNER TUBE with VALVE TUBE per detail 14-B. Slip BURNER TUBE over VALVE TUBE per detail 14-C. Fasten BURNER in place per detail 14-D. Hardware shown actual size 14-A Right Console (JD) #10-24 Stamped Wing Nut (2) Qty. 14-D Burner Valve Tube Burner Tube 14-B Caution: Assemble the wires BELOW the burner tubes! 14-C JD JD 11-D. Fasten the burner in place with two WINGNUTS (JD). Tighten all fasteners. Step 15 Assemble the BURNER to the LEFT CONSOLE. Slip BURNER TUBE through LEFT CONSOLE per detail 15-A. Move the Flexible Fuel Hose downward to give clearance for inserting the burner tube. Slip BURNER TUBE over VALVE TUBE per detail 15-C. The Flexible Fuel Hose and Wiring must be routed BELOW the burner tube per detail 15-D. Left Console Hardware shown actual size 15-A (JD) #10-24 Stamped Wing Nut (2) Qty. 15-D Valve Tube Flexible Fuel Hose Left Burner 15-B TEST THE IGNITER: A SPARK SHOULD APPEAR AT Flexible Fuel Hose ELECTRODE TIP. Burner Tube IF THE SPARK DOES NOT APPEAR: -CHECK THE WIRE CONNECTIONS TO THE 15-C MODULE. -CHECK PROPER ASSEMBLY OF FRESH 9-VOLT BATTERY. JD JD Caution: Assemble the wires BELOW the burner tubes! 15-D. Fasten the burner in place with two WINGNUTS (JD). 18) Assemble the DOOR LATCH to the PEDESTAL. Step 16 16-A KE Door Latch KE 16-A. Assemble the DOOR LATCH with two SCREWS (CW). [. . . ] Coleman, at its option, will repair or replace this product or any component of the product found to be defective during the warranty period. Replacement will be made with a new or remanufactured product or component. If the product is no longer available, replacement may be made with a similar product of equal or greater value. This warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferable. [. . . ]