User manual COLEMAN PM0606750

[. . . ] IMPORTANT ­ Please make certain that persons who are to use this equipment thoroughly read and understand these instructions and any additional instructions provided prior to operation. * * * * * * * 12 HP Yamaha OHV engine Cast-iron cylinder sleeve Low oil sensor Receptacles on control panel DIGITECHTM Digital Information Center 7 gallon metal fuel tank Portability Kit At a glance, the user can instantly see how much of the generator's output capacity is being used and how much power remains available. the display also indicates the time since last user reset and the total accumulated runtime of the generator. [. . . ] This could happen when you touch an appliance or cord that is " live " through faulty mechanism, damp or worn insulation, etc. 120/240 V, 30 Ampere Twistlock Receptacle A maximum of 30 amps may be drawn from the 120/240 volt receptacle, provided it is the only receptacle used. However, current must be limited to the nameplate rating. If the 120/240 volt receptacle is used along with the 120 volt receptacle, the total load drawn must not exceed the nameplate ratings. If this occurs, disconnect all electrical loads and try to determine the cause of the problem before attempting to use the generator again. Insert wheel spacer (item 39) into the center of the wheel (item 28). 25" bolt (item 32) and 3/8 washer (item 27) through the wheel (item 28), then through the wheel bracket on the carrier, with the offset side of the wheel hub against the wheel bracket. Blocking up the engine side of the generator, place the foot bracket (item 43) under the carrier channel. Thread a 5/16-18 x 4" bolt (item 42) with a rubber foot (item 29) through the mounting holes and thread a 5/16 flange nut (item 47) to the bolt to secure the foot bracket to the carrier. Caution: Do not over tighten so that the rubber foot material collapses. To lock the handle (item 25) in the extended position, align the holes in the handle brackets with the holes in the carrier brackets and insert the release pins (item 34). Warranty Coverage: Powermate Corporation (the Company) warrants to the original retail customer in North America that it will repair or replace, free of charge, any parts found by the Company or its authorized service representative to be defective in material or workmanship. This warranty covers the cost of replacement parts and labor for defects in material or workmanship. not Covered: · Transportation charges for sending the product to the Company or its authorized service representative for warranty service, or for shipping repaired or replacement products back to the customer; these charges must be borne by the customer. Engine is covered exclusively by a separate warranty from the engine manufacturer, included with the engine Manual. Warranty is voided if the customer fails to install, maintain and operate the product in accordance with the instructions and recommendations of the Company set forth in the owner's manual. [. . . ] 25 Nut, nyloc 3/8-16 Pin, release Cap, plastic Washer, flat 1/4 Nut whz 8mm Switch, Rocker Wheel spacer Grip, handle Bolt, 5/16-18 x 4 Bracket, foot Bolt, M8 x 16mm Bolt, 1/4-20 x 1 1/4 Bolt, 1/4-20 x 1 Nut, hex flg 5/16-18 Bolt, 5/16-18 x 1 1/4 Washer, star external 1/4 Screw #10 x . Generator head, Sumec Adapter, engine Rotor Stator Band, stator cover Bolt, M6 x 195 Support, bearing Brush module Screw flg M5 x 16mm AVR module Bolt, M5 x 230 Nut, nyloc M5 Terminal block Washer M5 Washer, lock M5 Nut M5 Cover, end Screw flg M5 x 8mm Fan Screw M5 x 20mm Bearing Stator harness Engines are covered through the engine manufacturer's warranty. Consult the accompanying engine manual or contact our service department for assistance. [. . . ]