User manual COMET LABS IPTEL

[. . . ] VoIP Telephone Adaptor User Manual Model Nr. IPTEL-H / IPTEL-S / IPTEL-M V1. 7 English Version Copyright 2004 ® Quick Guide Step 1: Broadband (ADSL/Cable Modem) Connections For IPTEL RJ45 LAN port to Router/ADSL as one of the A. Connect IPTEL-H / IPTEL-S / IPTEL-M following connections. B. Connect IPTEL RJ45 PC port to PC using a Category 5 LAN cable. [. . . ] Connect IPTEL RJ45 PC port to Notebook PC using a Category 5 LAN cable. Connect IPTEL RJ11 PHONE port to a Plain Old Telephone Set (POTS). Connect the Power Adaptor (5VDC) to the POWER outlet. The POWER and PHONE LED indicators will start flashing for about 10 seconds and OFF for a while, then flashing three times again. After the POWER LED is lit constantly, the IPTEL will be ready for configuration and VoIP calls. If the PHONE LED keep flashing, is idle, it indicates that IPTEL has successfully registered in the Gatekeeper (Refer to Section 7 & 8 for Gatekeeper Mode). Pick up the phone, the PHONE LED will be lit and you should hear a dial tone. Prepare for the IPTEL an IP address, a Subnet mask, and a Router IP address before making a VoIP call. These three can be available from your Internet Service Provider. The defaults of IP Address, Subnet mask, and Router IP Address for IPTEL are 192. 168. 1. 150, 255. 255. 255. 0, and 192. 168. 1. 254. Configurations Command modes can be entered from either the telephone or PC Telnet session and can be stored and remains in the flash memory even when the power is off. 6. 1 IP Configurations From Telephone 1) Pick up the phone, the PHONE will be lit and you should hear a dial tone. 2) Enter the IPTEL an IP Address, a Subnet mask, and a Router IP address as the following. Press #11 + IP Address Example: Press #11061020102004 if the IPTEL IP Address is 61. 20. 102. 4 Press #12 + Subnet mask Example: Press #12255255255000 if the Subnet mask is 255. 255. 255. 0 Press #13 + Router IP Address Example: Press #13061020102254 if the Router IP address is 61. 20. 102. 254 Note that you must press 3 digits for each byte of the IP address. 3) After entering each item, you will hear the dial tone for confirmation. If not, you will hear a busy tone indicating an invalid configuration. The defaults of IP Address, Subnet mask, and Router IP Address for IPTEL are 192. 168. 1. 150, 255. 255. 255. 0, and 192. 168. 1. 254, respectively. 3 7. Telephone Keypad Dialing You may now start making a VOIP call by dialing the IP address directly from the telephone. There are 5 different types of dialing for IPTEL; 1) Direct Static IP Dialing (#200): 12-15 digits for Point-to-Point and Point-to-Multiport Gateway static IP dialing. 2) Direct Static IP Dialing + Gatekeeper Mode Dialing (#201): 1-11 digits for Gatekeeper Mode dynamic IP dialing, and 12-15 digits for direct Point-to-Point and Point-to-Multiport Gateway static IP dialing. 3) Gatekeeper dialing mode (#202): 1-48 digits for Gatekeeper and Trunk Gateway such as Cisco 5300 4) Memory dialing (#80 - #99) for stored number dialing 5) Hot-line dialing mode (#401): In 3 seconds after hang-up, the number in #99 will be dialed. 7. 1 Point-to-Point Static IP calls 1) Press the IP address of the party you want to call as the following. Example: Press 211020102110 to call the party with IP address 211. 20. 102. 110 In 3 seconds, you should hear the ring back tone, and wait for the called party to answer, or you will hear a busy tone when the dialed number is busy or not available. 7. 2 Point-to-Multiport Gateway Static IP calls 1) Press the IP address + the extension port number Example: Press 061219023102900 to call the party with IP address of 61. 219. 23. 102 at extension port 900. In 3 seconds, you should hear the ring back tone, and wait for the called party to answer. 7. 3 Point-to-Point Gatekeeper Dynamic IP calls 1) Press the Alias Number Example: Press 112233 to call the party with alias number 112233 registered in the gatekeeper. [. . . ] Exit to enable PPPoE Note that the new dynamic IP from ISP will replace for the IP 192. 168. 1. 150 after enabling PPPoE, and the "telnet 192. 168. 1. 150" will not be valid any more until disabling PPPoE by pressing #050# from the telephone set. Now your registered VOIP alias number is 123456, and you may have your friend dial 123456 to call you at this IPTEL. 11 10. Commands Summary: Entered from Telephone Set (POTS) Cmds #01# #01 #03 #05 #11 #12 #13 #20 #21 #22 #23 #24 #25 #26 #30 #40 #01# #01xxxxx# #03+[0. . 999]+# #05+[0|1]+# #11+TA IP #12+Subnet Mask #13+Router IP #20+[0. . 2]+# #21+GK IP #22+GK id+# #23+Alias Name+# #24+Alias Number+# #25+Endpoint id+# #26+[0. . 32]+# #30+[0|1|2]+# #40+[0|1]+# 1 0 820 0 Format Defaults Descriptions Reset to Defaults Set Password xxxxx Volume Control PPPoE Enter From POTS POTS POTS POTS POTS POTS POTS POTS POTS POTS POTS POTS POTS POTS POTS POTS POTS POTS POTS Enter From POTS POTS POTS POTS POTS POTS 192168001150TA IP Address 255255255000Subnet Mask 192168001254Router IP Address 1 (enabled) GK Dialing Mode 061066159237GateKeeper IP Address GateKeeper id Alias Name Alias Phone Number Endpoint id Time To Live in minute Codec Selections Stored IP/Alias Number Stored IP/Alias Number Hot Line IP Address Digits 12 - 15 12 - 15 + 1 - 11 1 - 48 18 3 3 Descriptions Direct Static IP Dialing Direct Static IP Dialing + GK Mode Dialing GK Mode Dialing TFTP Download Server Dial Stored Number Dial Stored Number 0 (disabled) Hot Line Mode #80 #80+IP/Alias Number+# #99 #99+IP/Alias Number+# #99 #99+IP+# Dialing Format #200 #201 #202 *01 *80 *99 IP or IP+Port Number IP or IP+Port Number + Alias Phone Number Alias Phone Number *01+IP+F/W Version *80 *99 Note: (1) It is required from the telephone set (POTS) to press the "#" to complete the configuration, and it is not needed from PC telnet session. 12 Entered from PC Telnet session Cmd #01 #03 #05 #06 #07 #11 #12 #13 #20 #21 #22 #23 #24 #25 #26 #30 #40 #80 #99 #99 Format #01xxxxx #03+[0. . 999] #05+[0|1] #06+username #07+password #11+TA IP #12+Subnet Mask #13+Router IP #20+[0|1] #21+GK IP #22+GK id #23+Alias Name #24+Alias Number #25+Endpoint id #26+[0. . 32] #30+[0|1|2] #40+[0|1] #80+IP/Alias Number #99+IP/Alias Number #99+IP 1 0 800 Defaults Descriptions Set Password xxxxx Volume Control 0 (disabled) PPPoE Max 48 letters PPPoE username Max 48 letters PPPoE password 192168001150 TA IP Address 255255255000 Subnet Mask 192168001254 Router IP Address 1 (enabled) Disable/Enable GK Mode GateKeeper id Max 48 letters Alias Name Max 48 digits Alias Phone Number Endpoint id Time To Live in minute Codec Selections 061066159237 GateKeeper IP Address Enter From PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC 0 (disabled) Hot Line Mode Max 48 digits Stored IP/Alias Number Max 48 digits Stored IP/Alias Number Hot Line IP Address Note: (1) Power on/off will not reset to default settings. 13 11. [. . . ]