User manual COMET LABS ND23000

[. . . ] NAS : Network Area Storage Comet Labs, Inc. ND-23000 User Manual ND-23000 Series User Manual (Version: 4. 2) ©Copyright 2005. June 24, 2005 2 Note: Unless otherwise specified, "NAS" refers to Comet Labs ND-23000 models in this document. CUSTOMER SERVICE For the contact details of customer service and technical support, please refer to the registration card. [. . . ] Or you can assign a specific path for the share folder. The path cannot exceed 256 characters and cannot contain the characters below: ü Comment Enter a brief description for the share folder. The comment cannot exceed 128 characters. 56 · Access Control Once the network share is created, you can assign access rights to users or user groups: ü ü Deny access Access to the network share will be denied when this option is selected. Read only Users can read the files only on the network share when read only is assigned. ü Full access Users with full access are allowed to read, write, create, or delete files and folders on the network share. 57 · Property and Delete To edit the property of an existing network share, select a share and click Property. You can then edit the content of that share. You can also select to delete an existing network share. Click OK to confirm the deletion or Cancel to abort. 58 3. 9 System Tools System Tools enable you to optimize the maintenance and management of NAS. 3. 9. 1 SNMP Settings Enable SNMP (Simple Network Management Protocol) service and complete all necessary settings to manage network components of the server by SNMP. When enabling SNMP Trap Notification, a message will be sent to a specified trap host when an error occurs. 59 3. 9. 2 Alert Notification Enter the e-mail address of administrator and SMTP server IP address. In case of warning or malfunction, an email will be sent to the administrator automatically. 3. 9. 3 Restart/ Shutdown Select to restart or shut down NAS. 60 3. 9. 4 Hardware Settings You can enable or disable the hardware functions of NAS. Enable LCD panel setting function To enable users to configure TCP/IP settings via the LCD panel. Enable configuration reset switch By enabling this option, you can press the reset button for a few seconds to reset the administrator password and system settings to default. Enable hard disk standby mode Set the minutes when there is no access to the server and the hard disk will go to standby mode. Enable buzzer When buzzer is enabled, an alert sound will be played in case of system err or. Stop network services when a hard disk of RAID fails When a hard disk of RAID configuration fails, network services of NAS will stop. 61 3. 9. 5 UPS If your UPS device provides USB interface, you can enable UPS (uninterruptible power supply) support to protect your system from abnormal system shutdown caused by power outage. In case of utility power failure, the system will shut down automatically by probing the power status of the connected UPS unit. ü Enable UPS support To activate the UPS support, you can select this option. You can set the shutdown timer to turn off the system automatically after the system detects the AC power is abnormal. In general, the UPS can keep supplying the power for the system for about 5 to 10 minutes. But this depends on the maximum load of the UPS and the number of the loads connected to it. UPS Model Select the UPS model from the list. If the UPS model you are using is not available on the list, please contact our technical support. UPS IP If you have selected APC UPS with SNMP for UPS model, enter the IP address of the UPS. Note: When UPS support is not enabled, the Test button will not function. 62 3. 9. 6 System Update To update the firmware version of NAS, make sure you have obtained the correct version of image file. It is suggested to back up all existing data on NAS before updating the image. [. . . ] Enable AD Dom ain Member, and enter the domain name and the user name with administrator access right to that domain. Note: (1) Make sure that a fully qualified domain name such as qatest. com. tw has been filled in. (2) Make sure the user name with administrator access right to that domain. 129 3. When the following message appears after applying the settings in step 2, check the DNS IP. When the following message appears after applying the settings in step 2, domain name, domain user name, and the password. When the following message appears after applying the settings in step 2, check the time zone settings. Make sure the difference of your time and that of AD server is less than 5 minutes. If the time difference is larger than 5 minutes, you will not be able to add the domain member. 130 4. Upon successful adding of domain member, you can view the list for domain users and local users in User Management. 5. Go to Access Control in Network Share Management to configure the access control right of AD users for all available network shares. 131 Using AD users to access services To access services like FTP, Network Neighborhood, Apple Talk with an AD user account, add DomainName\ before the user name when logging in. 132 Adding NAS to Windows Server 2000 NT Domain 1. [. . . ]