User manual COMPAQ BLUETOOTH PENDANT HEADPHONES

[. . . ] 5 Bluetooth receiver components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3 Charging the Bluetooth audio adapter and Bluetooth receiver 4 Using the earbuds with the Bluetooth audio adapter (select models only) 5 Using the headphones with a Bluetooth-enabled computer Pairing using Windows Vista . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Pairing using Windows XP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 6 Using the audio line-in cable with other audio devices (select models only) 7 Terminating the headphone wireless connection Terminating a wireless connection with the Bluetooth audio adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Plays the next track of a CD or the next chapter of a DVD. NOTE: This button only works when connected to a Bluetooth-enabled computer. (5) Charging light Red: The receiver is charging. Off: The battery is fully charged. (6) (7) Volume down button Receiver status light Decreases headphone volume. A blinking blue light can indicate any one of the following states: Power: The receiver is turned on and the light blinks fast 3 times. Standby mode: After the receiver is turned on, the headphones go into standby mode and the light blinks slowly until the headphones are successfully paired with the audio device. 6 Chapter 2 Identifying components Pairing: After you press and hold the multifunction button for 3 seconds, the light blinks faster until the headphones successfully pair with the audio device. Paired: When the headphones successfully pair with the audio device, the light blinks slowly. (8) Previous/rewind button Off: The receiver is off and Bluetooth is deactivated. Plays the previous track of a CD or the previous chapter of a DVD. NOTE: This button only works when connected to a Bluetooth-enabled computer. (9) Multifunction button When the receiver is off, press and hold the button for 3 seconds to turn on the receiver and begin pairing. When the receiver is on and connected to a Bluetooth-enabled computer, briefly press the button to play or pause audio. When the receiver is on and connected to an audio device, briefly press the button to mute or restore the sound. When the receiver is on, press and hold the button for 3 seconds to turn off the receiver and deactivate Bluetooth. Bluetooth receiver components 7 3 Charging the Bluetooth audio adapter and Bluetooth receiver Before you can use the headphones, you must charge both the Bluetooth audio adapter and the Bluetooth receiver. They can be charged using a USB port on your computer or using the AC adapter (select models only). To charge the Bluetooth audio adapter and Bluetooth receiver, complete the following steps: CAUTION: When removing the USB charging cable from a device, prevent damage to cable connectors by grasping each connector and then pulling gently. Do not pull on the cable to remove it from the device. Be sure that the Bluetooth audio adapter and Bluetooth receiver are turned off. If the status lights are off, the Bluetooth audio adapter and Bluetooth receiver are turned off. Plug one of the two Mini-USB connectors into the Mini-USB port on the Bluetooth receiver (1). Plug the other Mini-USB connector into the Mini-USB port on the Bluetooth audio adapter (2). 8 Chapter 3 Charging the Bluetooth audio adapter and Bluetooth receiver 4. Plug the USB connector into the USB port (3) on the AC adapter or the computer. 9 5. If you are using the AC adapter, plug the AC adapter into an AC outlet. WARNING!To reduce the risk of electric shock or damage to the equipment, plug the AC adapter into an AC outlet that is easily accessible at all times. The charging light turns on while the devices are charging and turns off after the Bluetooth audio adapter and Bluetooth receiver are fully charged. NOTE: For safety and regulatory information, refer to the Regulatory, Safety and Environmental Notices. These notices are located on the HP Bluetooth Pendant Headphones Accessory User Guides disc and in Help and Support. 10 Chapter 3 Charging the Bluetooth audio adapter and Bluetooth receiver 4 Using the earbuds with the Bluetooth audio adapter (select models only) Before using the earbuds, be sure that the Bluetooth audio adapter and Bluetooth receiver are fully charged. To use the earbuds with the Bluetooth audio adapter, follow these steps: 1. [. . . ] A blinking blue adapter status light (2) indicates that the adapter is turned on and pairing. 20 Chapter 6 Using the audio line-in cable with other audio devices (select models only) 6. Press and hold the multifunction button (1) on the Bluetooth receiver for 3 seconds to turn on the receiver and begin pairing. A blinking blue receiver status light (2) indicates that the receiver is turned on and pairing. 7. Open your media player software, if necessary, to begin listening to music or other audio output. 21 7 Terminating the headphone wireless connection When you finish using the headphones, you should terminate the wireless connection to your computer or audio device. Choose one of the following two sections and follow the steps for terminating the connection to the Bluetooth audio adapter or to a Bluetooth-enabled device. 22 Chapter 7 Terminating the headphone wireless connection Terminating a wireless connection with the Bluetooth audio adapter To terminate the connection, complete the following steps: 1. Press and hold the Bluetooth receiver multifunction button for 3 seconds to turn off the receiver and deactivate Bluetooth. 2. Press and hold the Bluetooth audio adapter multifunction button for 3 seconds to turn off the adapter and deactivate Bluetooth. Terminating a wireless connection with the Bluetooth audio adapter 23 3. Unplug the Bluetooth audio adapter from the audio-out (headphone) jack of your computer or audio device. 24 Chapter 7 Terminating the headphone wireless connection Terminating a wireless connection with a Bluetoothenabled computer To terminate the connection, complete the following steps: 1. [. . . ]