User manual COMPAQ JETDIRECT PN1050 ADMINISTRATOR GUIDE REV 1

[. . . ] HP Jetdirect pn1050 Network Projector Manager Administrator's Guide © Copyright 2005 Hewlett-Packard Development Company, L. P. Reproduction, adaptation, or translation without prior written permission is prohibited, except as allowed under the copyright laws. The information contained in this document is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. [. . . ] The object identifier (OID) is . 1. 3. 6. 1. 4. 1. 11. 2. 4. 3. 7. 31. 0 and needs to be set to zero (0). You can choose to enable or disable this feature at any time using the Privacy Settings page under the Networking tab. ENWW Using the Embedded Web Server 52 Network Settings The Network Settings pages allow you to set or change configuration parameters for TCP/IP and SNMP protocols. To assign a parameter setting, enter the desired value and click Apply. TCP/IP The TCP/IP page provides configuration parameters summarized in Table 4. 3. Table 4. 3 Item IP Configuration Method TCP/IP Settings (1 of 3) Description Selects the method that the HP Jetdirect projector server will use for its IP configuration parameters: BOOTP (default), DHCP, Manual, or Auto IP. For BOOTP or DHCP, the IP parameters will be automatically configured by a BOOTP or DHCP server each time the projector server is powered on. If you select Manual, then basic IP parameters can be manually entered using this Web page, or using other available tools. If you select Auto IP, then a unique link-local address 169. 254. x. x will be assigned. For more information, see Chapter 3. Host Name Specifies a readable IP name (the SNMP SysName object) for the network device. The name must start with a letter and can end in a letter or number, up to 32 ASCII characters. The default name is NPIxxxxxx, where xxxxxx is the last six digits of the LAN hardware (MAC) address. Use this field to manually assign the Internet Protocol address on the HP Jetdirect projector server. The IP address is a four byte (32-bit) address in the form "n. n. n. n", where `n' is a number from 0 to 255. An IP address uniquely identifies a node on a TCP/IP network. Duplicate IP addresses on a TCP/IP network are not allowed. For more information on IP addresses, see Appendix A. IP Address Subnet Mask If subnetting is used, use this field to manually assign a subnet mask. A subnet mask is a 32-bit number that, when applied to an IP address, determines which bits specify the network and subnet, and which bits uniquely specify the node. For more information on subnet masks, see Appendix A. ENWW Using the Embedded Web Server 53 Table 4. 3 Item TCP/IP Settings (2 of 3) Description Identifies the IP address of a router or computer that is used to connect to other networks or subnetworks. Specifies the name of the Domain Name System (DNS) domain that the HP Jetdirect projector server resides in (for example, support. hp. com). It does not include the host name; it is not the Fully Qualified Domain Name (such as projector1. support. hp. com). Specifies the IP address of the primary Windows Internet Naming Service (WINS) server. The WINS server provides IP address and name resolution services for network computers and devices. Specifies the IP Address to be used for WINS if the primary WINS Server is unavailable. Specifies the IP address of a host computer that is configured to receive syslog messages from the HP Jetdirect projector server. [. . . ] Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. All advertising materials mentioning features or use of this software must display the following acknowledgment: "This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. The names "OpenSSL Toolkit" and "OpenSSL Project" must not be used to endorse or promote products derived from this software without prior written permission. For written permission, please contact openssl-core@openssl. org. [. . . ]