User manual COMPAQ MP1600

[. . . ] Compaq MP1600 Microportable Projector User's Guide Notice The information in this guide is subject to change without notice. COMPAQ COMPUTER CORPORATION SHALL NOT BE LIABLE FOR TECHNICAL OR EDITORIAL ERRORS OR OMISSIONS CONTAINED HEREIN; NOR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE FURNISHING, PERFORMANCE, OR USE OF THIS MATERIAL. This guide contains information protected by copyright. No part of this guide may be photocopied or reproduced in any form without prior written consent from Compaq Computer Corporation. [. . . ] Picture--Adjusts the gamma value or degree of contrast of darkness or light for the projected image. Color--Adjusts color balance to compensate for ambient conditions using three submenus: t t t s s s s s 7100°K--The factory default. Custom Color--Modify the color temperature balance. Saturation--Magnify the color intensity. English 1-19 s Digital Conversion--Improves picture stability of user modes by adjusting: #Clock--Increase/decrease the value to stretch or shrink the image on the screen. #Clock Phase--Increase/decrease the value to minimize video distortion or video jitter. distorted when adjusting the If the projector image becomes continue adjusting the values Clock and Clock Phase values, until the distortion disappears. To restore the factory settings, select Factory Reset in the on-screen menu. s Language--Select display from six languages in their native spelling. Select another language to display all menu functions in that language. Menu Location--Positions the on-screen menu at a convenient location on the projector screen; moves up and down, left and right. Management--Allows the user to control power saver characteristics of the display, or to view the cumulative lamp hours, reset the lamp hour timer, view the unit's serial number, or perform a Master Reset. Factory Reset--Resets the current operating option to its original factory setting. s s s 1-20 English Special On-Screen Messages Special on-screen messages will appear on the projection display to identify the following conditions: s Check Video Cable: Indicates the video cable may not be plugged into the projector or the selected video input is not accurate. Input Signal Out of Range: Indicates the projector is unable to access the appropriate input signal. 2 Inputs Active - Remove One: The projector has two data inputs: one is an analog D-Sub input and the other is a digital DFP input. This message indicates that both inputs are active simultaneously and the user should detach one of them. Going to Standby: Indicates the projector is entering a sleep mode or powering off the lamp. Lamp May Fail Soon, Replacement Suggested: Indicates the lamp is approaching failure. The message will remain on the screen for five seconds or until the on-screen menu Select button is pressed. s s s s English 1-21 Care and Maintenance This section explains how to care for and maintain your Compaq projector during normal everyday use. Protecting the Projector To protect your projector from overheating and other types of damage, follow these suggestions: s Use only a power source and connection appropriate for this projector as indicated on the marking label. Do not overload an electrical outlet, power strip, or convenience receptacle. The overall system load must not exceed 80 percent of the branch circuit rating. If an extension cord or power strip is used, make sure that the cord or strip is rated for the product and that the total ampere ratings of all products plugged into the extension cord or power strip do not exceed 80 percent of the extension cord or strip ampere ratings limit. Install the projector near an outlet that you can easily reach. Disconnect the product by grasping the plug firmly and pulling it from the outlet. Never disconnect it by pulling the cord. Unplug the projector from the wall outlet before cleaning. [. . . ] All power cord sets must be approved by an acceptable accredited agency responsible for evaluation in the country where the power cord set will be used. The power cord set must have a minimum current capacity of 10A and a nominal voltage rating of 125 VAC or 5 Amps at 250 volts AC, as required by each country's power system. B-6 Agency Regulatory Notices 4. The appliance coupler must meet the mechanical configuration of an EN 60 320/IEC 320 Standard Sheet C13 connector, for mating with appliance inlet on the rear of the unit. Country-Specific Requirements Power Cord Set Requirements: By Country Country Australia Austria Belgium Canada China Denmark Finland France Germany Italy Japan The Netherlands Norway Singapore Sweden Switzerland United Kingdom United States Accredited Agency EANSW OVE CEBC CSA CCEE DEMKO FIMKO UTE VDE IMQ MITI KEMA NEMKO PSB or PUB SEMKO SEV BSI UL Applicable Note Numbers 1 1 1 2 1 1 1 1 1 1 3 1 1 1 1 1 1 2 Notes: 1. The flexible cord must be <HAR> Type HO5VV-F, 3conductor, 1. 0 mm2 conductor size. [. . . ]