User manual COMPAQ NX6110 MAINTENANCE AND SERVICE GUIDE

[. . . ] Maintenance and Service Guide HP Compaq nx6110/nc6110 and nx6120/nc6120 Notebook PCs Document Part Number: 373146-001 February 2005 This guide is a troubleshooting reference used for maintaining and servicing the notebook. It provides comprehensive information on identifying notebook features, components, and spare parts; troubleshooting notebook problems; and performing notebook disassembly procedures. © Copyright 2005 Hewlett-Packard Development Company, L. P. registered trademarks of Microsoft Corporation. Intel, Pentium, and Celeron are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. [. . . ] Avoid contact with pins, leads, or circuitry. Turn off power and input signals before inserting or removing connectors or test equipment. 4. 7 Grounding Equipment and Methods Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation. When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps with a minimum of one megohm ±10% resistance in the ground cords. To provide proper ground, wear a strap snugly against the skin at all times. On grounded mats with banana-plug connectors, use alligator clips to connect a wrist strap. 4­6 Maintenance and Service Guide Removal and Replacement Preliminaries When standing, use foot straps and a grounded floor mat. Foot straps (heel, toe, or boot straps) can be used at standing workstations and are compatible with most types of shoes or boots. On conductive floors or dissipative floor mats, use foot straps on both feet with a minimum of one megohm resistance between the operator and ground. To be effective, the conductive strips must be worn in contact with the skin. Other grounding equipment recommended for use in preventing electrostatic damage includes: Antistatic tape Antistatic smocks, aprons, and sleeve protectors Conductive bins and other assembly or soldering aids Nonconductive foam Conductive tabletop workstations with ground cords of one megohm resistance Static-dissipative tables or floor mats with hard ties to the ground Field service kits Static awareness labels Material-handling packages Nonconductive plastic bags, tubes, or boxes Metal tote boxes Electrostatic voltage levels and protective materials Maintenance and Service Guide 4­7 Removal and Replacement Preliminaries Table 4-1 shows how humidity affects the electrostatic voltage levels generated by different activities. Table 4-1 Typical Electrostatic Voltage Levels Relative Humidity Event Walking across carpet Walking across vinyl floor Motions of bench worker Removing DIPS from plastic tube Removing DIPS from vinyl tray Removing DIPS from Styrofoam Removing bubble pack from PCB Packing PCBs in foam-lined box 10% 35, 000 V 12, 000 V 6, 000 V 2, 000 V 11, 500 V 14, 500 V 26, 500 V 21, 000 V 40% 15, 000 V 5, 000 V 800 V 700 V 4, 000 V 5, 000 V 20, 000 V 11, 000 V 55% 7, 500 V 3, 000 V 400 V 400 V 2, 000 V 3, 500 V 7, 000 V 5, 000 V A product can be degraded by as little as 700 V. Table 4-2 lists the shielding protection provided by antistatic bags and floor mats. Table 4-2 Static-Shielding Materials Material Antistatic plastic Carbon-loaded plastic Metallized laminate Use Bags Floor mats Floor mats Voltage Protection Level 1, 500 V 7, 500 V 5, 000 V 4­8 Maintenance and Service Guide 5 Removal and Replacement Procedures This chapter provides removal and replacement procedures. There are 62 screws and screw locks, in 11 different sizes, that must be removed, replaced, or loosened when servicing the notebook. Make special note of each screw and screw lock size and location during removal and replacement. Refer to Appendix C, "Screw Listing" for detailed information on screw and screw lock sizes, locations, and usage. Maintenance and Service Guide 5­1 Removal and Replacement Procedures 5. 1 Serial Number Report the notebook serial number to HP when requesting information or ordering spare parts. The serial number is located on the bottom of the notebook. Serial Number Location 5­2 Maintenance and Service Guide Removal and Replacement Procedures 5. 2 Disassembly Sequence Chart Use the chart below to determine the section number to be referenced when removing notebook components. Disassembly Sequence Chart Section 5. 3 Description Preparing the notebook for disassembly Battery pack Hard drive # of Screws Removed 0 2 loosened to remove the hard drive cover 1 loosened to remove the hard drive 6 to disassemble hard drive 0 0 1 loosened to remove the memory module/Mini PCI compartment cover 1 loosened to remove the memory module/Mini PCI compartment cover 5. 4 5. 5 5. 6 Notebook feet Bluetooth board External memory module 5. 7 Mini PCI Communications Card Å To prevent an unresponsive system and the display of a warning message, install only a Mini PCI device authorized for use in your notebook by the governmental agency that regulates wireless devices in your country. If you install a device and then receive a warning message, remove the device to restore notebook functionality. 1 5. 8 Optical drive Maintenance and Service Guide 5­3 Removal and Replacement Procedures Disassembly Sequence Chart (Continued) Section 5. 9 5. 10 5. 11 5. 12 5. 13 5. 14 5. 15 5. 16 5. 17 5. 18 5. 19 5. 20 5. 21 5. 22 5. 23 Description Keyboard Switch cover LED board Fan Heat sink Processor Modem board Internal memory module RTC battery Display assembly Top cover Speaker Digital media board USB/audio board System board # of Screws Removed 2 2 4 2 loosened 4 loosened 1 loosened 2 0 0 6 15 4 0 1 1 screw 4 screw locks on HP Compaq nc6110 and nc6120 models 2 screw locks on HP Compaq nx6110 and nx6120 models 2 screw locks 5. 24 Serial connector module 5­4 Maintenance and Service Guide Removal and Replacement Procedures 5. 3 Preparing the Notebook for Disassembly Before you begin any removal or installation procedures: 1. If you are unsure whether the notebook is off or in hibernation, turn the computer on, and then shut it down through the operating system. Disconnect all external devices connected to the notebook. Disconnect the power cord. Battery Pack Spare Part Number Information 6-cell, 4. 4-AHr 6-cell, 4. 4-AHr 6-cell, 2. 2-AHr 372772-001 383220-001 364602-001 4. Remove the battery pack by following these steps: a. Turn the notebook upside down with the rear panel toward you. Maintenance and Service Guide 5­5 Removal and Replacement Procedures b. Slide and hold the battery pack lock latch 1 to the right. [. . . ] The flexible cord must be Type VCT or VCTF, 3-conductor, 1. 00 mm² conductor size. The wall plug must be a two-pole grounding type with a Japanese Industrial Standard C8303 (7 A, 125 V) configuration. B­4 Maintenance and Service Guide C Screw Listing This appendix provides specification and reference information for the screws and screw locks used in the notebook. All screws and screw locks listed in this appendix are available in the Screw Kit, spare part number 378235-001. Maintenance and Service Guide C­1 Screw Listing Table C-1 Phillips PM2. 0×4. 0 Screw Head Width 4. 0 mm mm Color Black Qty. 3 Length 4. 0 mm Thread 2. 0 mm Where used: 1 2 screws that secure the hard drive cover to the notebook (screws are captured on the cover by C clips; documented in Section 5. 3) 2 1 screw that secures the memory module/Mini PCI compartment cover to the notebook (screw is captured on the cover by a C clip; documented in Section 5. 6) Phillips M2. 0×4. 0 Screw Locations C­2 Maintenance and Service Guide Screw Listing Table C-2 Phillips PM2. 5×13. 0 Spring-loaded Hard Drive Retention Screw Head Width 5. 5 mm mm Color Silver Qty. [. . . ]