User manual COMPAQ W185Q

[. . . ] v185e/v185es/v185w/v185ws/w185/w185e/W185q LCD Monitor User's Guide The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. HP assumes no responsibility for the use or reliability of its software on equipment that is not furnished by HP. [. . . ] Press the Power button (E) to turn the monitor on and off. The power indicator lights up when the monitor is on. The monitor must be turned on for the other control buttons to work. Set the resolution (Setting the Optimal Resolution) and adjust the volume (Adjusting the Volume). Adjust the onscreen display (OSD) settings (Adjusting On-screen Display Settings). 11 External Controls A B C Auto button Menu button ­ (minus) button Automatically fine-tunes the image quality. Navigates backward through the OSD menu and decreases adjustment levels. If the OSD menu is inactive, activates the Volume decrease. Navigates forward through the OSD menu and increases adjustment levels. If the OSD menu is inactive, activates the Volume increase. Fully powered = green Sleep mode = amber Sleep timer mode = flashing amber D E F + (plus) button Power button Power LED See Technical Support FAQs for more information. 12 Settings Setting the Optimal Resolution The recommended resolution for this monitor is 1366 x 768. To configure the monitor to this resolution, complete the setup procedure and make sure that the monitor is connected to the computer. Turn the monitor on and do the following: 1 Click the Windows Start Button®, and then click Control Panel. 2 Under Appearance and Personalization, click Adjust Screen Resolution. 3 Set the resolution slide bar to 1366 x 768. NOTE: If 1366 x 768 is not shown, download the monitor driver from the Web. See Using the Monitor for instructions. Adjusting the Volume While the monitor is turned on but the OSD menu is inactive, press the volume increase and decrease (plus and minus) buttons to adjust volume to the desired level. The preset value is 50. Locking and Unlocking the OSD To change the lock status of the on-screen display (from locked to unlocked, or from unlocked to locked) press and hold the Menu button for 10 seconds while the monitor is on. If the OSD is locked, the message "OSD Lock" displays for 10 seconds. 13 Adjusting On-Screen Display Settings Use the OSD menu to adjust the screen image and change settings. To access the OSD menu: 1 If the monitor is not already on, press the Power button to turn the monitor on. 2 Press the Menu button to activate the OSD menu. 3 Press the ­ (minus) and + (plus) buttons to navigate through the functions. The software download pages for your monitor will be displayed. Download and install the driver and software files using the instructions in the download pages. Using the Auto-Adjustment Function Press the Auto button to optimize the screen performance for VGA (analog). If your monitor is using VGA (analog) input, auto-adjustment can correct the following image quality conditions: Fuzzy or unclear focus Ghosting, streaking, or shadowing effects Faint vertical bars Thin, horizontal scrolling lines An off-center picture 18 Technical Support FAQs Technical Support FAQs (Frequently Asked Questions) Problem & Question Power LED is not on. [. . . ] To locate defective pixels, the monitor should be viewed under normal operating conditions and in normal operating mode at a supported resolution and response rate, from a distance of approximately 50 cm (16 in). We expect that, over time, the industry will continue to improve its ability to produce displays with fewer cosmetic imperfections, and we will adjust guidelines as improvements are made. For more information about your v185e / v185es / v185w / v185ws / w185 / w185e / W185q Monitor, refer to the HP Web site at: http://www. hp. com/support Agency Regulatory Notices Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ]