User manual COMPX C2174-2DC-KD

[. . . ] Recycling of the appliances organised by your manufacturer will thus be undertaken in optimum conditions, in accordance with European directive 2002/96/CE relating to electrical and electronic equipment waste. Contact your local authority or retailer for how to have used appliances collected or collection points. 1 Working Principle A B C Induction coils Glass insulating hob top Ferrous pan base EN The induction principle The principle of induction is based on a magnetic effect. When you place your cookware on a cooking zone and you turn it on, the electronic circuits in your cooking hob produce “induced” currents in the bottom of the cookware which instantly raise its temperature. This heat is then transmitted to the food. [. . . ] Please refer to the pan guide in the description section of this guide for further details. 3 Additional functions and safety Features EN Protection against overflows. In case of overflow, or of a metallic object or wet cloth placed on the control areas, the hob turns itself off, the displays light up and a beep sounds. Clean the hob or remove the object, then begin cooking again. Temperature limiter. Each cooking zone is equipped with a safety sensor that constantly monitors the temperature of the bottom of the cookware. If you leave empty cookware on a zone which is turned on, it will automatically limit the power in order to prevent damage to the cookware or hob. Residual heat. After a long cooking period, the zone used can remain hot for several minutes. An ‘’H’’ flashes during this period. Do not put your hand on the zone. Auto-Stop system. If you forget cooking is in progress, after a predefined time, this safety function will automatically turn off your hob (from 1 to 10 hours depending on the power setting). “AS” displays and a beep sounds after about 2 minutes. Press on the main selector to delete this information. Select the zone required and adjust the power as required. press the timer controls “G” and using the “+” or “-”keys select the cooking time required. The appliance will now count down the time and turn off as required. When the time remaining is less than 1 minute the display will indicate seconds remaining. At the end of the time a beep will indicate the end of cooking. 5 Additional Functions and Safety Features Pre Heat / Heat up EN Pre-heat / Heat upThis Function will preheat the contents of the pan to boiling temperature before reducing to your selected power. To select the function turn on the required zone then press the “-“on the power selection keys, “HU” is shown on the display, Select the power level to be maintained after the initial heat up ( this must be level 7 or above ). During the pre-heat phase the display will alternate between the selected power level and “HU”, once the preheating is complete the display will revert to the power level only. This feature can be used in conjunction with the timer functions. For example you can set the appliance to preheat a pan of pasta to a boil reduce the pan to a simmer then time the entire cooking phase to ensure perfect results every time. Boil Function The boil function allows the user to heat to boiling point a quantity of water prior to adding food such as Pasta or vegetables and then maintaining the boiling for a period of time set by the user. To operate the boil function touch the “boil” icon on the touch pad, the display will then show the volume of water to be boiled in litres. The volume can then be adjusted using the “+” or “-” keys (0. 5l, 1l, 1. 5l, 2l, 2. 5l, 3l, 4l, 5l or 6l) confirm by pressing the “boil” key. [. . . ] Use a scraper for glass to remove the large bits, follow with rough side of a disinfectant sponge then wipe off. Any appliance sealed to the work-surface using silicone sealant or similar may result in damage to both the appliance and work-surface should it need to be removed. The use of sealants may result in the appliance being unserviceable and as such may be excluded from warranty repairs. 9 Installation Guide Electrical connection EN Hook-up of 220-240V ~32 amp Hook-up of 220-240V ~16 amp •Hook-up of 2x230V 2L+2N ~ - 16A •Hook-up of 400V 2N ~ - 16A •Hook-up of 400V 3~ - 16A 10 Help Guide Problems on installation Posssible Causes A special code / display ap­ Working normally pears across the ccontrol panel Your installation blows a fuse Incorrect electrical connection / trip Only 1 side of the appliance works Incorrect electrical connection The hob produces an odour during the first cooking ses­ sions New appliance EN What should you do? Nothing this code will turn off after 30 seconds or if the zone is turned on Check electrical supply connection Check electrical supply connection Nothing. The smell will disapear with use. Problems after switching on You observe that Possible causes What should you do? The hob does not operate and The machine is not switched Check electrical supply, mains there are no indicator lights on or correctly connected to switches / circuit breaker / on the display. [. . . ]