User manual COMPX C3205

[. . . ] AVISO: El tomacorriente debe estar instalado cerca del equipo y debe quedar bien accesible. VARNING: Det matande vägguttaget skall placeras nära apparaten och vara lätt åtkomligt. LET OP: Het stopcontact dient in de buurt van de kassa en gemakkelijk toegangbaar te zijn. CAUTION: For a complete electrical disconnection pull out the AC adapter. [. . . ] Please install three new alkaline batteries LR6 (“AA” size) before programming and operating the cash register. Before inserting the battery, make sure the AC adapter is connected and the power is on. Step 3 Installing a Paper Roll For the printer, you must install the paper roll provided with the register, even when you program the register for not printing receipt. 2. Open the paper guide and set a paper roll in the paper roll cradle as per the diagram. Mount the paper holding plate onto the takeup spool. Set the spool on the bearing, and press F to take up excess slack in the paper. VAT(Tax) rate programming Your cash register is preprogrammed so that VAT1 through VAT4 are calculated manually. You can program a VAT rate. Advanced Programming Before starting programming, set the mode switch to the Z/PGM mode. Reading and Resetting Sales X Reports This report, when taken in the X/Flash mode, prints the accumulated information of sales. Taking an X report is a good way to do a mid-day check on daily sales. You can take X reports any number of times, because they do not affect the cash register’s memory. To issue an X report, turn the mode switch to the X/Flash position and press 9 u A Q B u u To finish programming: Department Preset Unit Price Programming Dept. counter and total Percent counter and total Item void counter and total Void mode counter and total Taxable 1 total Tax 1 (VAT) total D 1. Remove the printer cover. The paper cutter is mounted on the printer cover. Be careful not to cut yourself. Parameters A: VAT (Tax) 1: 1 VAT (Tax) 2: 2 VAT (Tax) 3: 3 VAT (Tax) 4: 4 B: Tax rate (00. 0000% to 99. 9999%) x10000 (Default: 00. 0000%) Example TAX1 = 7. 0000 % 6. Replace the printer cover. For additional basic information of programming and operation, please refer to the part of “Quick Start Operations” in the “FULL DETAILED INSTRUCTION MANUAL”. 1 (for discount) / 0 (for premium) Percent rate in 4 digits (00. 00% to 99. 99%) x 100 ( u) Programming the percent rate (00. 00 to 99. 99%) Q % %( u) D 5. Close the battery cover. 6. Replace the printer cover. To display the time and date Set the mode switch to the REG position, and press Q once to display the time or press Q twice to display the date. Press l to cancel the time/date display. Example 15. 5%: 1550 %u For additional information of programming and operation, please refer to the part of “Advanced Programming” in the “FULL DETAILED INSTRUCTION MANUAL”. *1 Printed in the Z report only. *2 Difference by rounding is printed here in case Australian rounding is applied. *3 Not printed in case that the exchange rate is set to 0. 000000. *4 Not printed in case that “Cheque and credit operation when tendering in foreign currency” is set to “No” on EURO programming, and/or the exchange rate is set to 0. 000000. Entries Flow of Register Use During the Day Before store opens • Make sure the AC adapter is connected. • Make sure there is enough paper (refer to “Maintenance”) • Check the date and time (refer to “Getting Started”) • Insert the mode key into the mode switch and turn the key to the REG position. Basic Sales Entries (Department Entries) Listed below is a basic sales entry example when selling items by cash. 7) for cash and receiving 25. 00 from your customer. (tax system: manual VAT1-4) 1. Set the mode switch to the REG position. 2. Enter the price for the department item (in case of 15. 00). [. . . ] For the programming, also refer to the “Percent Key Programming” section. Replacing the Ink Roller When printing becomes faded, replace the existing ink roller with a new one available from COMPX. 9. Press A, and the change due is displayed and the drawer is opened. 10. Tear off the receipt and give it to the customer (in case you programmed receipt printing) with his or her change displayed. 11. Close the drawer. C C After closing • Calculate sales [X report, Z report] (refer to “Reading and Resetting Sales”) • Store cash in drawer elsewhere (refer to “Drawer Handling”) • Set the mode key to the OFF position “ ”. To completely shut off the power, disconnect the AC adapter from the power receptacle. D • When paid by cheque, press C instead of A. [. . . ]