User manual CONCORD ULTIMAX

[. . . ] Using the ULTIMAX child car seat To safeguard your child you have opted for our CONCORD ULTIMAX seat. This product is manufactured under strict quality controls. Its excellent safety features work best when the seat is used in accordance with legal requirements. Be sure, therefore, to comply fully with the instructions for its installation and use. [. . . ] To take the child out, press the red "Press" button on the belt buckle of the harness system. click 4. Adjusting the seat to the child's size / adjusting the head support and harness 4. 1 0033-05 0249-03 4. 2 0105-04 4. 3 0034-02 A Grasp the head support at the top and pull it forwards. You can then set it to the height that is right for your child. There are six possible different positions. Always make sure the belt is positioned correctly, as shown in 4. 2, illustration (A). B When the child is strapped in, the shoulder belt should feed horizontally to the back or incline slightly upwards, see illustration (A). If the shoulder belt feeds downwards as shown in the illustration (B), then the belt must be repositioned and inserted through the next slot up. To do this proceed as follows: To adjust the shoulder belt positions, the seat shell must be removed from the base unit (see 1. 1 and 1. 2)!Pull away the back trim located on the back of the seat shell. 4. Adjusting the seat to the child's size / adjusting the head support and harness 4. 4 0036-06 0250-02 4. 5 0040-04 The central adjuster is located at the front of the seat, beneath the cover. Release the central adjuster by pushing the small flap up (see illustration), and then pull the belts through to the front (do not pull on the belt padding!). On the rear of the seat shell, separate the two belts from the connecting piece. 4. Adjusting the seat to the child's size / adjusting the head support and harness 4. 6 0123-04 0251-01 4. 7 0042-07 Then pull the two belts out to the front through the backrest and the seat cover. Now thread both belts from the front through the cover and into the required slot. Pull the two metal clasps on the back of the seat out of their recesses and fit them through the belt openings in the seat shell. On the back you must thread both belts back into the connecting piece, then tighten the belt at the front by the central belt. Please check that the left and right harness belts are both adjusted in the same way. 4. Adjusting the seat to the child's size / adjusting the harness / shortening the belts 0252-02 4. 8 0124-03 4. 9 0143-04 click On the back of the seat, clip the metal clasps back into position. They must engage with an audible "click". Thread the belts back into the connecting piece, as shown in the illustration. Finally, clip in the back trim. When does the belt system need to be shortened?If you cannot tighten the child seat belt sufficiently by pulling on the central adjuster at the front of the seat, then it will be necessary to shorten the belt system. Adjusting the seat to the child's size / shortening the belts 4. 10 0045-05 0253-01 4. 11 0051-06 Remove the seat shell from the base unit and lay the shell upside down on a clean surface. Release the elastic tapes on the cover and pull the cover back a little. [. . . ] The ULTIMAX child car seat has been tested in a simulated headon crash at an impact speed of 50 kph against a solid obstacle. This complies with the international test standard ECE R 44 04 which forms the basis for all tested restraint systems. If used according to legal requirements, and given adherence to the instructions for installation and use, this device should prevent or reduce injury to children up to three years of age or with a body weight of up to 18 kg in the event of an accident, depending on the type and severity of accident. As is the case with the use of safety belts for adults, a child safety device does not replace the need for responsible and prudent driving behaviour. 9. [. . . ]