User manual CONSTRUCTA CG640J7

[. . . ] en Dishwasher summary of instructions Brief and handy: everything your dishwasher needs . . . Before using for the first time, read the operating instructions! Adjusting the water softening system* Read off the correct setting for your water hardness . . . Quickly sorted . . . How to adjust the water softening system ­ Rotate the programme button from the 12 o'clock position by one notch to the left. ­ Switch on the main switch and hold down for at least 3 seconds. [. . . ] PLOP! Turn on tap Water flows in . . . Select programme Quick, economical or intensive . . . Overview of programmes This overview indicates the max. The programmes which correspond to your appliance can be found on your appliance fascia. Duration in minutes Intensive Normal Eco Gentle Quick Prerinse 70_ 65_ 50_ 40_ 45_ 600N 9000 285 820 ( 8705) The programme data are values measured in the laboratory in compliance with Standard EN 50242. Deviations is practice are possible. 138 1, 65 Water consumption in litres 16 Power consumption in kWh 140 1, 60 16 140 1, 05 13 75 0, 90 14 30 0, 80 10 19 0, 05 4 Switch on the appliance Here we go . . . Press main switch, running time of the selected programme is indicated. Additional programmes ** Soaking . . . of utensils in the bottom basket, programme starts automatically, 5 g of extra detergent on the open door!reduces washing time reduces drying time Flexibility . . . Half load . . . for a few items, saves water, energy and time Extra dry . . . improves the drying result by increased temperature in the final rinse (Please take care with delicate dishes) Time selection Switch off the appliance Everything o. k. . . . When the display is on 0 (end of programme), press the main switch. h. . . . switches on as soon as you press the time selection button: Alters the programme start in hourly steps ** some models Maintenance and care Filters Check and, if required, clean: Rotate filter cylinder, remove filter system For perfect rinsing results Rinse under running water Insert Screw on filter system. NOTE MARK! Waste water pump * * some models ­ Set main switch to OFF ­ Scoop out any water ­ Remove the filters ­ Remove the cover (A) ­ Check the inner compartment for foreign objects and, if required, remove foreign objects ­ Re-insert the cover (B) ­ Re-insert the filters and screw into position Spray arms Remove blockages/ deposits Pull up lower arm Clean under running water (if required, use a toothpick) Insert lower arm Screw on upper arm click 3 2 Unscrew upper arm A . . . as it is worth doing it yourself! Remedial action Fault Possible causes Remedial action B Rectifying minor faults yourself . . . Fault Possible causes "Check water supply" display lights up Supply fitting jammed or calcified Open supply fitting. If the flow rate is less, replace the supply fitting. Utensils are not clean Sand or gritty residue on the utensils Utensils are situated close together or one above the other Too little detergent Unsuitable programme selected Spray arm nozzles blocked Filters dirty, not seated firmly Filters dirty, not seated firmly Spray arms blocked Separate the utensils, prevent contact points. Follow manufacturer's instructions (detergent). Arrange the utensils so that the spray arms can rotate freely. Residual water in the appliance and "Check water supply" display lights up Waste water pump blocked The programme has not yet ended Waste water hose is blocked or kinked Clean waste-water pump (see above). [. . . ] 3 seconds the digital display indicates 0. ­ The programme sequence lasts approx. ­ When the programme has run, switch off the main switch. Loading the dishwasher correctly . . . Dishwasher-proof utensils (not soiled with ash, wax, lubricating grease, ink or adhesive labels; remove large remnants of jam, milk products and food according to the operating instructions and check that the spray arms can rotate freely. [. . . ]