User manual CONTINENTAL EDISON CE60LCD22SD10

[. . . ] Protection of Shutting Down Automatic Shutting down Automatic is a safety protection function for your induction hotplate. It will shut down automatically if you forget to turn off your cooker. The default working times for various power levels are shown in the following table: Power level 1~5 6~10 11~14 The heating zone shut down automatically after 8 hours 4 hours 2 hours 1 hours *Remind: The patient with a heart pacemaker shall use this product under the guidance of the doctor. For the purpose of installation and use, a minimum of 50 mm space shall be preserved around the hole. [. . . ] The cable must be checked regularly and replaced by authorized technicians only. Lock Function key Figure (7) Instructions For Use Preparation Before Using: After power on, the buzzer beep once, all the indicators light up for 1 second and then go out, which indicates the induction hotplate enters the state of standby. Put the pot in the center of the heating zone. Select zone 1), with a corresponding power level indicator flashing. At the moment, press the "+" button, the indicator displays "8", or press the "-" button, the indicator displays "1", then adjust the power u levels sing the "+", "-" button or the slider Or press the "+" and "-" buttons simultaneously, the power setting immediately chang to 0, and the relevant cooking zone switches off. AND See the attached table "the max power of each heating zone" for the power specific to each heating zone. After the "ON/OFF" button is pressed, the induction hotplate will restore to its standby state if no any operation is carried out within one minute. Boost function To get a quicker heating speed, there is a function named "Boost" will satisfy your requirement. Directly press the " Boost" button after selecting the heating zone, with the power level indicator showing "P. The boost function only operates for 5 minutes, after which the cooking zone returns to its orginal setting. As the boost function is activated , the other cooking zone of the same side is limited under level 2 automatically(for example, when the 2nd cooking zone's boost function is activated, the 1st cooking zone which is of the same left side will be limited under level 2 automatically). Select the relevant cooking zone, press the "Fry" button, the indicator shows "F", then this relevant cooking zone starts fry function mode Power of each heating zone are as follows: Heating Zone 1 2 3 4 Max. The above power may vary if the material or the size of pot is differet. This induction hotplate is able to identify multiple heating appliances, and you can test them according to one of the following methods: 1. place the appliance in the heating zone. If the corresponding heating zone displays a power level, it shows the suitability of the appliance; if " " flashes, it shows the appliance does not fit in the induction cooking. If there is attraction between them, it shows the appliance also fits in the induction cooking. Please use a dedicated power protection air switch; Never directly wash the induction hotplate with water so as to avoid dangers. Never have the induction hotplate to work without food inside, otherwise its operational performance may be affected and danger may happen. For sealed food such as canned goods, please do not heat them before opening their covers so as to avoid any dangers of explosion due to heating expansion. After being used for a long time, the corresponding heating zone of the induction hotplate is till hot. We suggest that you should periodically check that there are no object (glass, paper, etc) that could obstruct the inlet under your induction hotplate. [. . . ] For further information regarding the treatment, recover and recycling of this product please contact your local council, your household waste disposal service, or the shop where you purchased it. For more detailed information about treatment, recovery and recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. You can easily clean the surface of the induction hotplate if following the methods given in the table. Immerse in hot water then wipe it Cleaning sponge dry Special cleaning Immerse in hot water then wipe it sponge for ceramic dry with abrasive sponge glass Apply white vinegar to the polluted zone, then wipe it dry with soft cloth or a special article available in local markets Special adhesive for ceramic glass Use a scraper suitable for ceramic glass (to protect glass, a silicon product is preferred) to remove residuals If an abnormality comes up, the induction hotplate will enter the protective state automatically and display corresponding protective codes: Component Solutions Please contact the supplier Power on, and then restart after the temperature around returns to be normal. [. . . ]