User manual COOLER MASTER V8

[. . . ] Do not disassemble any part of the product: no user-serviceable parts are inside. The product should only be repaired or serviced by qualified and authorized service personnel. defected pieces must be replaced by original (spare) parts. Batteries: keep batteries out of the reach of children. [. . . ] Make sure that the batteries are not short circuited and are not disposed in fire (danger of explosion). In case of improper use or if you have opened, altered and repaired the product yourself, all guarantees expire. The supplier does not accept responsibility in the case of improper use of the product or when the product is used for purposes other than specified. The supplier does not accept responsibility for additional damage other than covered by the legal product responsibility. Our ebode proprietary eIR2xTM (pronounce Irex) Technology guarantees a high level of immunity for InfraRed noise from direct sunlight, CFL lighting and Flat Panel TV’s (including Plasma, LCD and LED). 31-12-2010 3 IR Link Pro Flush This kit contains two 3IREDB Triple Blinking Emitters for control of 6 devices, and a 1IRQC Quick Connect cable for direct control of popular Audio/Video Receivers (e. The IR Link Pro Flush Kit runs on a 12VDC mains adapter (included) and is expandable with extra IR Link Receivers in different rooms. The IR Link Pro Flush Kit is a mains powered InfraRed Extender System that allows full remote control operation of audio/video components (such as your Blu-ray player, A/V Receiver, DVR, Satellite Box, Cable Tuner, etc. ) which are located behind closed cabinet doors, in other rooms, or other concealed and/or out-of-sight locations. An InfraRed Extender in general consists of an IR (InfraRed) capture device, the IR Receiver, a distribution circuit/connecting block, the IR Hub, and finally the IR LED output, the IR Emitter, which flashes the IR signal to the A/V component. It includes an IRLPRO Flush Mount IR Receiver with 4 interchangeable, coloured top covers (black, white, brushed chrome and brass), an IRHUB4 Connecting Hub with 4 Emitter outputs + Status input Jumper Cable, two 3IREDB Triple Blinking Emitters, a 1IRQC Quick Connect cable and a 12VDC Power Supply. Operation The IR repeater system should now operate each of the controlled components. When the system is operating correctly, you should see a Blue "talk-back" LED flash on the front of the IRLPRO Flush IR Receiver when you aim your hand held remote control(s) at it and press the buttons. How to avoid and solve possible problems Although the ebode IR Link Pro Flush is equipped with proprietary eIR2xTM (pronounced Irex) Technology, which guarantees a high level of immunity of InfraRed noise from direct sunlight, CFL lighting and Flat Panel TV’s (including Plasma, LCD and LED), in rare cases, the IRLPRO Flush IR Receiver may have to be moved to a different location if the unit is picking up unexpected interference. This interference may, in severe cases, prevent the system from working. After repositioning, check to see if the IR Link Pro Flush operates the satellite Receiver or other components. If the IR Link Pro Flush still does not work, reposition the IRED Emitter(s). It may not be located directly over the component’s InfraRed receiving "window". Consult the owner's manual of the unit or the manufacturer for the exact location of the InfraRed "window". IMPORTANT: For installations involving more than two remote rooms, use the services of a competent professional audio/video installer experienced in InfraRed remote control systems. 5mm TRRS plug pin configuration from tip to sleeve: o Tip = yellow = IR Data o Ring 1 = black = Ground = Thin wire 3 o Ring 2 = red = +12VDC = Thin wire 4 outside, opposite end to yellow/white striped o Sleeve = white = Status = Thin wire 2 next to yellow/white striped • Reception range: Up to 10 meters, depending on local conditions and remote control used. Indicates InfraRed reception only when Emitter(s) are connected. [. . . ] Maximum transmission length: 300m with category cable (UTP, use white striped together for GND, and use 2 solid colours for IR and 2 solid colours for 12VDC). In case of STATUS wiring, use 1 solid wire for IR and 1 solid wire for Status. In case of long run un-shielded cable (> 25m), it may be necessary to connect a 470 Ohm 1/8Watt resistor in parallel between IR and GND at the IRHUB connecting block. IRHUB4 Connecting Hub • 1x Power: 230V~50Hz, 12VDC 200mA (supplied) • 1x 4-Way Wago screw terminal for IR, GND, 12VDC and Status • 1x Power Status JP2 input: 5 – 12VDC @ 10mA minimum or 5 – 12VAC at 47-63HZ • 1x JP to C-plug 2. [. . . ]