User manual CORBERO FD5140I

[. . . ] " This appliance is designed to be operated by adults. Children should not be allowed to tamper with the controls or play with the appliance. " Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. " This appliance should be serviced by an authorized Service Centre, and only genuine spare parts should be used. [. . . ] If the domestic power supply socket is not earthed, connect the appliance to a separate earth in compliance with current regulations, consulting a specialist technician. The Manufacturer declines all responsibility if the above safety precautions are not observed. This appliance complies with EEC directive number 87/308 of 2/6/87 relative to radio interference suppression. This appliance complies with the following E. E. C. Directives: - 73/23 EEC of 19. 2. 73 (Low Voltage Directive) and subsequent modifications; - 89/336 EEC of 3. 5. 89 (Electromagnetic Compatibility Directive) and subsequent modifications. Bottom hinge Remove the bottom hinge (A) and refit it on the lefthand side of bottom base of the cabinet, which h a s p re - d r i l l e d holes for fixing. A D119 , A f t e r h a v i n g re moved the top and bottom hinges (following the instructions in the previous paragraphs), re m o v e t h e t w o d o o r s ; u n s c re w t h e t w o s c re w s which secure the centre hinge to the appliance cabinet; Centre hinge D121 Cleaning the interior Before using the appliance for the first time, wash the interior and all internal accessories with lukewarm water and some neutral soap so as to remove the typical smell of a brand-new product, then dry thoroughly. Do not use detergents or abrasive powders, as these will damage the finish. turn the hinge upside down and fit it on the other side of the cabinet, after having removed the covers which mask the holes provided for fixing; use the covers to mask the holes left open; refit the two doors and tighten the top and bottom hinges. 13 Important The centre hinge can be moved horizontally by about 3 mm to allow alignment of the doors, as follows: slacken the two screws securing the centre hinge to the cabinet and move the hinge until the doors are in line. Warning Once the opening direction of the doors has been changed, check that the magnetic seal adheres to the cabinet. If the ambient temperature is cold (for example in winter), the seal may not adhere perfectly to the cabinet. In this case, wait for the seal to adapt naturally to its new position, or accelerate this process by heating up the area involved with a normal hairdryer. Warning A top seal is supplied loose with the appliance; this seal must be fitted before inserting the appliance into the recess (the holes for fixing it are pre-drilled). A plastic sealing strip is also supplied; snap it into place between the appliance and the kitchen unit. Fig. 3 Building and securing the appliance into the tall kitchen unit Recess height 1446 mm Recess depth 550 mm Recess width 560 mm D030 Fitting the appliance into the recess (Fig. 4) To position and secure the appliance inside the recess, proceed as follows: Fig. 1 A The dimensions of the recess for fitting the appliance into a tall kitchen unit must be as indicated in the table above. 200 cm Ventilation is provided though the bottom grille, se25 D140 cured to the bottom of the appliance, and through an opening to be cut in the base of the kitchen unit (minimum size 200 cm2 Fig. 1). 2 50 8 A D117 position the appliance inside the tall kitchen unit, pushing it against the inner side of the unit on which the door opens (Fig. 4); make sure that, with the door closed, the appliance is set back 8 mm from the front of the recess (Fig. Using the 6 screws provided, secure the bottom ventilation grille and the top seal (the holes are pre-drilled). Fig. 2 540 50 L P H A vent outlet, 50 mm deep by 540 mm wide must be cut in the top of the unit (Figs. 1-2) D010 14 Appliance door opening device (Fig. 4-5) The accessories pack supplied with the appliance contains a device to allow the kitchen unit and appliance doors to be opened simultaneously. Fig. 5 C A B The device consists of guide (A), blocks (B), securi n g s c re w s a n d block covers (C). To fi x g u i d e ( A ) , drill the door as shown in Fig. [. . . ] If the light does not come on when the door is open, check that it is screwed into place properly. If it still does not light up, change the bulb. The rating is shown on the light bulb cover. Fig. 10 Periodic cleaning Never use metal objects for cleaning your appliance as it may get damaged. [. . . ]