User manual CORBERO FM820-2

[. . . ] AL ANU T M STE OOKLE E RVE HIS B E ONS EEP T C EA Y AND K L D REA LIBRO DE INSTRUCCIONES OPERATING INSTRUCTIONS FM 820/2 (TT 160**) FRIGORÍFICO REFRIGERATOR 200364186 ES GB SP/C/27-2. (02. ) GB Before installing and using the appliance read this user's instruction book carefully. It contains safety precautions, hints, information and ideas. If the refrigerator is used in compliance with the instructions written, it will operate properly and provide you with greatest satisfaction. [. . . ] Information on your local disposal sites may be obtained from your municipal authorities. The materials used on this appliance marked with the sympol are recyclable. Some useful information and advice The variable shelves are worth paying attention to, which increases the usefulness of the fresh food compartment considerably. Rearranging the shelves is also possible when the door is open at an angle of 90°. Hints and ideas In this chapter practical hints and ideas are given about how to use the appliance to reach maximum energy saving and there is environmental information about the appliance as well. 22 GB Maintenance Defrosting Bleeding part of the moisture of cooling chamber in form of frost and ice goes with the operation of the refrigerator. Thick frost and ice has an insulating effect, so it reduces cooling efficiency as the temperature increases, it needs more energy, at a certain thickness it does not allow the door of the frozen food compartment to open, possibly the door can be broken. We recommend to defrost the frozen food compartment once a week and when the frost is more than 4-5 mm. Put the drip tray into closed position, and switch off the appliance by removing plug from the mains socket. Defrosting usually takes several hours, at the end you can remove the collected water from the drip tray by placing another tray under it then pull out the plastic cork at the bottom. When the thaw water came out, replace the cork and plug the appliance to the mains socket. Regular cleaning It is recommended to wash the inside of the refrigerator in 3-4 weeks time. Household cleaner or soap must not be used. After you made it no-current wash the appliance using lukewarm water and wipe it. Clean the magnet door rubber profile with clean water. After cleaning plug the appliance to the mains socket. It is practical to clean and defrost the frozen food compartment at a time and when it is empty. Dust and dirt collected on the back of the refrigerator, condenser is recommended to be removed once or twice a year. When the refrigerator is not in use Break the circuit of the appliance. Defrost and clean it as written before. In case the appliance will not be used for a long time follow these steps: Leave the door open to avoid a build up of air inside. 23 GB Trouble shooting How to change the bulb Should the light fail to work you can change it as below: Break the circuit of the appliance. Unscrew the plate screw fixing the lamp cover, then take the lamp cover off in the direction of arrow and the bulb can be changed. (Type of the bulb: Mignon 322, 230 V, 15 W, E 14 thread) After changing bulb replace the lamp cover, screw the plate screw and apply voltage to the appliance. The lack of light does not influence operation of the refrigerator. If something does not work During operation of the appliance some smaller but annoying trouble can often occur, which does not require calling a technician out. In the following chart information is given about them to avoid unnecessary charges on service. We draw your attention that operation of appliance goes with certain sounds (compressor- and circulating sound). This is not trouble, but means normal operation. We draw it to your attention again that the appliance operates discontinuously, so the stopping of compressor does not mean being nocurrent. [. . . ] Then screw in the one screw in the place set free on the other side as well as the adjustable feet (2 pieces) and set up the box. 26 For refitting the upper door holder take out the screws (2 pieces) fixing the plastic top on the back of the box. Push back the top and lift it from the fixing elements. Unscrew the screws fixing the upper door holder (2 pieces). After unscrewing turn over the pin in the door holder plate in the direction of the arrow. Fit and fix the door holder plate on the other side without displacing the door. [. . . ]