User manual CREDA HBW810

[. . . ] Has been correctly installed. 3 FP089-01 Creda Gas Hob (W810) 12/09/2001 5:02 pm Page 4 FOR YOUR SAFETY When used properly, your appliance is completely safe but as with any product there are certain precautions that must be observed. PLEASE READ THE PRECAUTIONS BELOW BEFORE USING YOUR APPLIANCE. ALWAYS q q q q q q q q q q q Always make sure you understand the controls prior to using the appliance. Always keep children away from the appliance when in use as the surfaces will get extremely hot during and after cooking. Always make sure all controls are turned off when you have finished cooking and when not in use. [. . . ] Oven chemical cleaners, aerosols and oven pads. Caustic cleaners such as these will etch the surface and attack the metal frame. Bath and sink cleaners may mark the surface. VITREOUS ENAMEL HOB, PAN SUPPORTS AND BURNER CAPS. Wipe with a cloth wrung out in hot soapy water. Stubborn stains can be removed with a cream paste or liquid cleaner. STAINLESS STEEL. Wipe with a cloth wrung out in hot soapy water followed by a wipe with a cloth wrung out in clear water and then dried with a soft clean cloth. ALUMINIUM BURNER BODIES AND RINGS. Wipe with a cloth wrung out in hot soapy water only; do not use abrasives. Use a nylon brush to remove any cleaning materials, water or dirt from the burner bodies. Re-assemble as in the diagram below. CONTROL KNOBS. Wipe over the knobs with a soft cloth wrung out in hot soapy water or mild non-abrasive cleaner. Then, after wiping with a cloth wrung out in clear water, dry with a soft clean cloth. Never use scouring pads or abrasive cleaners/powders which may scratch the surface. BURNER ASSEMBLY 7 FP089-01 Creda Gas Hob (W810) 12/09/2001 5:02 pm Page 8 SOMETHING WRONG ? IF THE IGNITION DOES NOT WORK Is the electricity switched on?If the electricity supply has failed, the burners can be lit with a match. If only a hotplate burner is failing to ignite, check that the burner body and cap are seated correctly and that the slots in the burner body are not blocked (see care and cleaning). May we wish you many years of carefree successful cooking. Disposal of your product To minimise the risk of injury to children please dispose of your product carefully and safely. Remove all doors and lids (where fitted). Remove the mains cable (where fitted) by cutting off flush with the appliance and always ensure that no plug is left in a condition where it could be connected to the electricity supply. To help the environment, Local Authority instructions should be followed for the disposal of you product. This appliance conforms to the following EEC Directives: Low Voltage Equipment 73/23/EEC 93/68/EEC Electromagnetic Compatibility 89/336/EEC 92/31/EEC 93/68/EEC Gas Appliances 90/396/EEC 93/68/EEC 8 FP089-01 Creda Gas Hob (W810) 12/09/2001 5:02 pm Page 9 INSTALLATION - electrical requirements WARNING ­ THIS APPLIANCE MUST BE EARTHED. Connection to the electricity supply should be made via a properly earthed, readily accessible wall socket which is adjacent to but not directly above, and not more than 1. 25m away from the appliance and capable of electrical isolation. Should this plug not fit the socket outlet in your home it should be cut off and replaced with a suitable plug as outlined below. NOTE: The removed plug cannot be used for any other appliance and should therefore be properly disposed of and not left where children might find it and plug it into a supply socket ­ with the obvious consequent danger. IF THE FITTED PLUG IS REMOVED The flexible mains lead must be correctly connected as below to a three pin plug of not less than 13 amp capacity. 1363 fused plug is used, it must be fitted with a 3 amp fuse which is approved to B. S. IMPORTANT: The wires in the mains lead fitted to this appliance are coloured in accordance with the following code: GREEN AND YELLOW ­ EARTH BLUE ­ NEUTRAL BROWN ­ LIVE Blue to Neutral Cord Clamp Green & Yellow to Earth Brown to Live 3 Amp Fuse As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:­ The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol or coloured green or green and yellow. The wire which is coloured blue must be connected to the terminal which is marked with the N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. [. . . ] Ensure that the hob is functioning correctly prior to use. Instruct the user in the operation of the hob. 12 FP089-01 Creda Gas Hob (W810) 12/09/2001 5:02 pm Page 13 INSTALLATION Fig. 1 IMPORTANT Minimum unobstructed depth 30mm 558 mm Front edge of worktop 50mm mm 489 Worktop thickness Preferred 30-40mm 19mm minimum recommended Fig. 2 FIXING CLAMP Note: Do not over tighten the hob clamps as distortion of the hob may occur. 13 FP089-01 Creda Gas Hob (W810) 12/09/2001 5:02 pm Page 14 INSTALLATION INSTRUCTIONS LPG Conversion Instructions for Model W810, BG05 Read the Gas Hob instructions before conversion, installation and using the Gas Hob. [. . . ]