User manual CRESTON CEN-UPS1250

[. . . ] Crestron CEN-UPS1250 Uninterruptible Power Supply Operations & Installation Guide This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON Regulatory Compliance This unit has been manufactured to comply with the following Standards for Safety in the United States, Canada and Mexico. Federal Communications Commission (FCC) Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user's authority to operate the equipment. [. . . ] Connect the Device Due to the unique filtering provided by the CEN-UPS1250, Crestron recommends that you connect the AV components as labelled on the rear panel of the unit. To ensure ground loops are eliminated and to ensure there is no audible hum in your speaker system, ground all AV components to the ground binding post (marked G) located on the rear panel. Make the necessary connections as called out in the illustration that follows this paragraph. When making connections to the CEN-UPS1250, consider that the included AC cable cannot be extended. Operations & Installation Guide ­ DOC. 6635D Uninterruptible Power Supply: CEN-UPS1250 · 15 Uninterruptible Power Supply Hardware Connections for the CEN-UPS1250 SATELLITE IN: From Cable or Antenna CABLE IN: From Cable or Antenna Crestron CEN-UPS1250 SATELLITE OUT: To TV/Receiver or Modem CABLE OUT: To TV/Receiver or Modem BANK 1 DIGITAL DEVICES: To Control Systems, Power Supplies , Touchpanels and Media Servers EXTERNAL BATTERY: For Optional Battery Sold By APC INPUT 120 V 47-63 Hz 12A: Main Power Input Ground BANK 2 DISPLAYS: To LCD Displays, Plasma Displays and Projectors BANK 3 ANALOG DEVICES: To Adagio Control Systems and Tuners BANK 4 HI-CURRENT DEVICES: To Amplifiers ENV PROBE : From External Temperature / RH Sensor LAN: 10/100 BASE-T Ethernet to LAN SERVICE PORT: For Factory Configuration Only TELCO IN: From Telephone Line COMPUTER: To PC TELCO OUT: To Telephone or Modem NOTE: The SERVICE PORT is for factory use only. To prevent accidental use, it comes with a plug installed. Ground Wire Connections Proper grounding is required. Connect the ground from the CEN-UPS1250 to earth ground. (Refer to the grounding diagram in the front of this manual. ) 16 · Uninterruptible Power Supply: CEN-UPS1250 Operations & Installation Guide ­ DOC. 6635D Crestron CEN-UPS1250 Uninterruptible Power Supply Programming Software Have a question or comment about Crestron software?Answers to frequently asked questions (FAQs) can be viewed in the Online Help section of the Crestron website. To post a question or view questions you have submitted to Crestron's True Blue Support, log in at http://support. crestron. com. First-time users will need to establish a user account. Earliest Version Software Requirements for the PC NOTE: Crestron recommends that you use the latest software to take advantage of the most recently released features. The latest software is available from the Crestron website. Crestron has developed an assortment of Windows-based software tools to develop a controlled system. For the minimum recommended software versions, visit the Version Tracker page of the Crestron website (www. crestron. com/versiontracker). Programming with Crestron SystemBuilder Crestron SystemBuilder is the easiest method of programming but does not offer as much flexibility as SIMPL Windows. For additional details, download SystemBuilder from the Crestron website and examine the extensive help file. Programming with SIMPL Windows NOTE: While SIMPL Windows can be used to program the CEN-UPS1250, it is recommended to use SystemBuilder for configuring a system. SIMPL Windows is Crestron's premier software for programming Crestron control systems. It is organized into two separate but equally important "Managers". Configuration Manager Configuration Manager is the view where programmers "build" a Crestron control system by selecting hardware from the Device Library. To incorporate the CEN-UPS1250 into the system, drag the CEN-UPS1250 from the Ethernet Control Modules | Ethernet I/O Control folder of the Device Library and drop it in the System Views. Operations & Installation Guide ­ DOC. 6635D Uninterruptible Power Supply: CEN-UPS1250 · 17 Uninterruptible Power Supply Locating the CEN-UPS1250 in the Device Library Crestron CEN-UPS1250 2. The system tree of the control system displays the device in the appropriate slot with a default IP ID as shown in the following illustration. C2Net Device, Slot 8 3. [. . . ] Authorized returns must be shipped freight prepaid to CRESTRON, 6 Volvo Drive, Rockleigh, N. J. or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a 15% restocking fee plus shipping costs on any products returned with an RMA. [. . . ]