User manual CRESTON CLSI-C6RF

[. . . ] Crestron CLS-C6RF ILux® Integrated Lighting System with infiNETTM Operations Guide This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON Regulatory Compliance This product is Listed to applicable UL Standards and requirements by Underwriters Laboratories Inc. As of the date of manufacture, the CL-C6RF has been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling. Federal Communications Commission (FCC) Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user's authority to operate the equipment. [. . . ] It is organized into two separate, but equally important "Managers". Configuration Manager Configuration Manager is the view where programmers "build" a Crestron control system by selecting hardware from the Device Library. To incorporate the CLS-C6RF into the system, first drag a C2N-MNETGW gateway icon from the Wireless Receivers | Wireless Receivers (RF) folder of the Device Library and drop it in the System Views panel. Then, drag the CLS-C6RF/CLS-C6MRF icon from the Lighting | Wall Dimmers/Switches (infiNET CLW Series) folder and drop it on the C2N-MNETGW icon. Locating the C2N-MNETGW in the Device Library Locating the CLS-C6RF in the Device Library 30 · iLux® Integrated Lighting System with infiNETTM: CLS-C6RF Operations Guide - DOC. 6418B Crestron CLS-C6RF 2. iLux® Integrated Lighting System w/infiNETTM The system tree of the control system displays the device in the appropriate slot with a default MNET ID as shown in the following illustration. C2Net Device, Slot 9 3. 4. Additional CLS-C6RF devices are assigned different MNET ID numbers as they are added. If necessary, double click a device to open the "Device Settings" window and change the RF ID, as shown in the following figure. "CLS-C6RF Device Settings" Window 5. Programming Manager The ID code specified in the SIMPL Windows program must match the MNET ID of each unit. Programming Manager is the view where programmers "program" a Crestron control system by assigning signals to symbols. The symbol can be viewed by double clicking on the icon or dragging it into Detail View. A description for each signal in the symbol is described in the SIMPL Windows help file (F1). Example Program An example program for the CLS-C6RF is available from the Crestron Web site (www. crestron. com/exampleprograms). Operations Guide - DOC. 6418B iLuxTM Integrated Lighting System with infiNETTM: CLS-C6RF · 31 iLuxTM Integrated Lighting System w/infiNETTM Crestron CLS-C6RF Uploading and Upgrading Crestron recommends using the latest programming software and that each device contains the latest firmware to take advantage of the most recently released features. However, before attempting to upload or upgrade it is necessary to establish communication. Once communication has been established, files (for example, programs or firmware) can be transferred to the control system (and/or device). Finally, program checks can be performed (such as changing the device ID or creating an IP table) to ensure proper functioning. Establishing Communication Use Crestron Toolbox for communicating with the CLS-C6RF; refer to the Crestron Toolbox help file for details. There are two methods of communication Direct Serial Direct Serial Communication PC Running Crestron Toolbox Serial via Crestron Cable STCP-502 or Equivalent CLS-C6RF The RS-232 mini phone jack port on the CLS-C6RF connects to the serial port on the PC via the supplied serial cable. Use the Address Book in Crestron Toolbox to create an entry using the expected serial communication protocol (RS232, auto-detect baud rate, no parity, 8 data bits, 1 stop bit, XON/XOFF disabled, RTS/CTS disabled). icon); Display the CLS-C6RF's "System Info" window (click the communications are confirmed when the device information is displayed. 2. Indirect Serial Indirect Serial Communication CEN-RFGW-EX infiNET EX CLS-C6RF LAN Serial, Control System LAN or USB PC Running Crestron Toolbox · · The CLS-C6RF connects to the C2N-MNETGW gateway via infiNET; the gateway connects to the control system via Ethernet. Establish communications between the PC and the control system as described in the latest version of the 2-Series Reference Guide (Doc. 6256). 32 · iLux® Integrated Lighting System with infiNETTM: CLS-C6RF Operations Guide - DOC. 6418B Crestron CLS-C6RF iLux® Integrated Lighting System w/infiNETTM Programs and Firmware Program or firmware files may be distributed from programmers to installers or from Crestron to dealers. Firmware upgrades are available from the Crestron Web site as new features are developed after product releases. [. . . ] Shipments arriving freight collect or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a 15% restocking fee plus shipping costs on any products returned with an RMA. Return freight charges following repair of items under warranty shall be paid by CRESTRON, shipping by standard ground carrier. In the event repairs are found to be non-warranty, return freight costs shall be paid by the purchaser. 2. 3. CRESTRON Limited Warranty CRESTRON ELECTRONICS, Inc. [. . . ]