User manual CRESTON DIN-2MC2

[. . . ] Crestron Green LightTM DIN-2MC2 DIN Rail Motor Control Operations & Installation Guide This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON Regulatory Compliance This product is Listed to applicable UL Standards and requirements by Underwriters Laboratories Inc. As of the date of manufacture, the DIN-2MC2 has been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling. Federal Communications Commission (FCC) Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user's authority to operate the equipment. [. . . ] 6665B Crestron DIN-2MC2 DIN Rail Motor Control 4. If necessary, double click a device to open the "Device Settings" window and change the Net ID, as shown in the following figure. "Device Settings: Crestron DIN-2MC2" Window 5. The ID code specified in the SIMPL Windows program must match the Net ID of each unit. Refer to "Identity Code" on page 9. Program Manager Program Manager is the view where programmers "program" a Crestron control system by assigning signals to symbols. The symbol can be viewed by double clicking on the icon or dragging it into Detail View. Each signal in the symbol is described in the SIMPL Windows help file (F1). Example Program An example program for the DIN-2MC2 is available from the Crestron website (www. crestron. com/exampleprograms). Operations & Installation Guide ­ DOC. 6665B DIN Rail Motor Control: DIN-2MC2 · 17 DIN Rail Motor Control Crestron DIN-2MC2 Uploading and Upgrading Crestron recommends using the latest programming software and that each device contains the latest firmware to take advantage of the most recently released features. However, before attempting to upload or upgrade it is necessary to establish communication. Once communication has been established, files (for example, programs or firmware) can be transferred to the control system (and/or device). Finally, program checks can be performed (such as changing the device ID or creating an IP table) to ensure proper functioning. Establishing Communication Use Crestron Toolbox for communicating with the DIN-2MC2; refer to the Crestron Toolbox help file for details. There is a single method of communication: indirect communication. Indirect Communication PC Running Crestron Toolbox Serial, Ethernet or USB Control System Cresnet DIN-2MC2 DIN-2MC2 connects to control system via Cresnet: 1. Establish communication between the PC and the control system as described in the latest version of the 2-Series Control Systems Reference Guide (Doc. 6256) which is available for download from the Crestron website (www. crestron. com/manuals). Use the Address Book in Crestron Toolbox to create an entry for the DIN-2MC2 using the expected communication protocol (indirect). Select the Cresnet ID of the DIN-2MC2 and the address book entry of the control system that is connected to the DIN-2MC2. Display the DIN-2MC2's "System Info" window (click the icon); communications are confirmed when the device information is displayed. 18 · DIN Rail Motor Control: DIN-2MC2 Operations & Installation Guide ­ DOC. 6665B Crestron DIN-2MC2 DIN Rail Motor Control Programs and Firmware Program or firmware files may be distributed from programmers to installers or from Crestron to dealers. Firmware upgrades are available from the Crestron website as new features are developed after product releases. One has the option to upload programs via the programming software or to upload and upgrade via the Crestron Toolbox. [. . . ] or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a 15% restocking fee plus shipping costs on any products returned with an RMA. Return freight charges following repair of items under warranty shall be paid by CRESTRON, shipping by standard ground carrier. [. . . ]