User manual CRESTON DM-TX-201-C

[. . . ] Crestron DM-TX-201-C DigitalMedia 8GTM Shielded Twisted Pair Transmitter 201 Operations & Installation Guide This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON Regulatory Compliance As of the date of manufacture, the DM-TX-201-C has been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling. Federal Communications Commission (FCC) Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user's authority to operate the equipment. [. . . ] Display the "System Info" window of the DM-TX-201-C (click the icon); communications are confirmed when the device information is displayed. 2. 3. 4. Operations & Installation Guide ­ DOC. 6958A DigitalMedia 8GTM STP Transmitter 201: DM-TX-201-C · 21 DigitalMedia 8GTM STP Transmitter 201 USB Communication via DM Switcher Crestron DM-TX-201-C PC Running Crestron Toolbox USB DM Switcher DM 8G DM-TX-201-C To establish USB communication between the PC and the DM switcher: 1. Use the Address Book in Crestron Toolbox to create an entry using the expected communication protocol (USB). When multiple USB devices are connected, identify the DM switcher by entering "DM-MD8X8", "DM-MD16X16", or "DM-MD32X32" in the Model textbox, the unit's serial number in the Serial textbox, or the unit's hostname in the Hostname textbox. The hostname can be found in the "System Info" window in the section marked Ethernet; however, communications must be established in order to see this information in the "System Info" window. icon); communications Display the "System Info" window (click the are confirmed when the device information is displayed. 2. Communication via LAN Port TCP/IP Communication via LAN Port of DM-TX-201-C LAN PC Running Crestron Toolbox DM-TX-201-C To establish TCP/IP communication between the PC and the DM-TX-201-C via the LAN port of the DM-TX-201-C: 1. Use the Device Discovery Tool in Crestron Toolbox to find the IP address of the DM-TX-201-C. The tool is available in Toolbox version 1. 15. 143 or later. NOTE: When the DM-TX-201-C is used in a standalone configuration (not used with a DM switcher), DHCP is enabled by default. If desired, a default IP address (192. 168. 1. 236) can be assigned by holding down its SETUP button while applying power. This IP address overwrites any previous settings and remains until it is changed. Use the Address Book in Crestron Toolbox to create an entry for the DM-TX-201-C using the TCP connection type, and enter the IP address of the DM-TX-201-C. Display the "System Info" window of the DM-TX-201-C (click the icon); communications are confirmed when the device information is displayed. 3. 22 · DigitalMedia 8GTM STP Transmitter 201: DM-TX-201-C Operations & Installation Guide ­ DOC. 6958A Crestron DM-TX-201-C 4. DigitalMedia 8GTM STP Transmitter 201 (Optional) If additional changes to TCP/IP settings are desired, do the following: a. Assign an IP address, IP mask, and default router for the DM-TX-201-C via the Crestron Toolbox (Functions | Ethernet Addressing). Close the "System Info" window. In Crestron Toolbox, change the Address Book entry for the DM-TX-201-C so that it uses the IP address assigned in step 4a. Display the "System Info" window of the DM-TX-201-C (click the icon); communications are confirmed when the device information is displayed. b. d. Firmware Firmware files may be distributed from programmers to installers or from Crestron to dealers. Firmware upgrades are available from the Crestron website as new features are developed after product releases. For details on upgrading, refer to the Crestron Toolbox help file. [. . . ] For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program. If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances. It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice. [. . . ]