User manual CRESTON DM-TX-201-S

[. . . ] Crestron DM-TX-201-S DigitalMedia 8GTM Fiber Transmitter 201 Operations & Installation Guide This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON This device includes an aggregation of separate independent works that are each generally copyrighted by Crestron Electronics, Inc. , with all rights reserved. One of those independent works, Linux Bridge Project, is copyrighted under the GNU GENERAL PUBLIC LICENSE, Version2, reproduced in "GNU General Public License" on page 39, where the corresponding source code is available at: ftp://ftp. crestron. com/gpl. All brand names, product names and trademarks are the property of their respective owners. [. . . ] Program Manager Program Manager is the view where programmers "program" a Crestron control system by assigning signals to symbols. The symbol can be viewed by double-clicking on the icon or dragging it into Detail View. Each signal in the symbol is described in the SIMPL Windows help file (F1). Operations & Installation Guide ­ DOC. 7068A Fiber Transmitter: DM-TX-201-S · 27 DigitalMedia 8GTM Fiber Transmitter Crestron DM-TX-201-S Uploading and Upgrading Crestron recommends using the latest programming software and that each device contains the latest firmware to take advantage of the most recently released features. However, before attempting to upload or upgrade it is necessary to establish communication. Once communication has been established, files (for example, firmware) can be transferred to the device. Finally, the IP table of the device can be configured. Establishing Communication Use Crestron Toolbox for communicating with the DM-TX-201-S; refer to the Crestron Toolbox help file for details. A PC running Crestron Toolbox communicates with the DM-TX-201-S in the following ways: · Via a DM switcher using TCP/IP or USB communication. TCP/IP provides a faster method of communication than USB. · Via the LAN port of the DM-TX-201-S using TCP/IP communication. In this scenario, the DM-TX-201-S is used in a standalone configuration (not used with a DM switcher). Communication TCP/IP Communication via DM Switcher via DM Switcher LAN PC Running Crestron Toolbox DM Switcher DM 8G Fiber DM-TX-201-S To establish TCP/IP communication between the PC and the DM-TX-201-S via the DM switcher: 1. Establish communication between the PC and the DM switcher as described in the latest version of the DigitalMedia Switchers Operations Guide (Doc. Use the Device Discovery Tool in Crestron Toolbox to find the IP address of the DM-TX-201-S. The tool is available in Toolbox version 1. 15. 143 or later. 28 · Fiber Transmitter: DM-TX-201-S Operations & Installation Guide ­ DOC. 7068A Crestron DM-TX-201-S DigitalMedia 8GTM Fiber Transmitter 3. Use the Address Book in Crestron Toolbox to create an entry for the DM-TX-201-S using the TCP connection type, and enter the IP address of the DM-TX-201-S. Display the "System Info" window of the DM-TX-201-S (click the icon); communications are confirmed when the device information is displayed. USB Communication via DM Switcher PC Running Crestron Toolbox USB DM Switcher DM 8G Fiber DM-TX-201-S To establish USB communication between the PC and the DM switcher: 1. Use the Address Book in Crestron Toolbox to create an entry using the expected communication protocol (USB). When multiple USB devices are connected, identify the DM switcher by entering "DM-MD8X8", "DM-MD16X16", or "DM-MD32X32" in the Model textbox, the unit's serial number in the Serial textbox, or the unit's hostname in the Hostname textbox. The hostname can be found in the "System Info" window in the section marked Ethernet; however, communications must be established in order to see this information in the "System Info" window. Display the "System Info" window (click the icon); communications are confirmed when the device information is displayed. Operations & Installation Guide ­ DOC. [. . . ] If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program. If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances. It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. [. . . ]