User manual CRESTON HD-EXT1-C QUICK START GUIDE

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual CRESTON HD-EXT1-C. We hope that this CRESTON HD-EXT1-C user guide will be useful to you.

Lastmanuals help download the user guide CRESTON HD-EXT1-C.


Mode d'emploi CRESTON HD-EXT1-C
Download
Manual abstract: user guide CRESTON HD-EXT1-CQUICK START GUIDE

Detailed instructions for use are in the User's Guide.

[. . . ] HD-EXT1-C HDMI® over Shielded Twisted Pair Extender quickstart guide 1 Introduction The HD-EXT1-C provides an HDMI® extender that consists of the HD-TX1-C transmitter and HD-RX1-C receiver. Operating as a pair, the HD-TX1-C and HD-RX1-C transmit uncompressed digital high definition video, audio, and control signals up to 330 feet (100 meters) over a single DM-CBL-8G shielded twisted pair (STP) cable. [. . . ] Mounting of the HD-RX1-C on a wall is shown below. Mounting the HD-RX1-C on a Rack Rail Mount the HD-RX1-C on the front or rear rail of a rack as follows: 1. Position either the left or right mounting flanges of the device so that the holes align with the holes in the rack (mounting of right mounting flanges is shown below). Secure the device to the rack using two rack mounting screws (not supplied). 4 Connections Connecting the HD-TX1-C and HD-RX1-C to Ground Connect the ground wire on the HD-TX1-C and the chassis ground lug on the HD-RX1-C to earth ground (building steel). HD-TX1-C Ground Wire NOTE: The OFF position of the SW1 DIP switch is reserved for factory use only. 3 Mounting Mount the HD-TX1-C and HD-RX1-C in any of the following ways as appropriate for your installation: (HD-TX1-C only) In a one-gang electrical box On a flat surface On a rack rail Mounting Screws (4) (Not Supplied) HD-EXT1-C Rack Mounting Screws (Not Supplied) IR OUT GS COM G TX RX G HDMI OUT HD-RX1-C Ground Lug (Continued on following page) 1 For Regulatory Compliance information, refer to the latest version of Doc. 7023A (2028987) 11. 10 www. crestron. com ©2010 Specifications subject to change without notice. 888. 273. 7876 201. 767. 3400 Crestron is a registered trademark of Crestron Electronics, Inc. HDMI is a trademark or registered trademark of HDMI Licensing LLC in the United States and other countries. HD-EXT1-C quickstart guide 4 Connections (Continued) HDMI® over Shielded Twisted Pair Extender Connecting the 24 VDC Power Jack on the HD-TX1-C or HD-RX1-C Only one 24 VDC power pack (supplied) powers both the HD-TX1-C and HD-RX1-C. Connect the power pack to either the 24 VDC power jack of the HD-TX1-C or HD-RX1-C as desired: If the power pack is connected to the HD-TX1-C, power is sent to the HD-RX1-C over the STP cable that connects the AV OUT port of the HD-TX1-C to the AV IN port of the HD-RX1-C. CONTROL SYSTEM Connecting HDMI and Control Ports on the HD-TX1-C Connecting the HDMI IN Port. Using an HDMI cable (not supplied), connect the HDMI IN port to the HDMI output port of the audio/video source. Connect the IR IN or COM control port or both as follows: IR IN: Using an IR cable (not supplied), connect the 2-pin terminal block of the IR IN port to the IR output port of the control system. COM (RS-232): Using a data communications cable (not supplied), connect the 3-pin terminal block of the COM port to the COM port of the control system. Connecting HDMI and Control Ports on the HD-RX1-C Connecting the HDMI OUT Port. Using an HDMI cable (not supplied), connect the HDMI OUT port to the HDMI input port of the receiving device. Connect the IR OUT or COM control port or both as follows: IR OUT: Using the Crestron® IRP2 emitter (not supplied), connect the 2-pin terminal block of the IR OUT port to the IR input port of the device to be controlled. COM (RS-232): Using a data communications cable (not supplied), connect the 3-pin terminal block of the COM port to the COM port of the device to be controlled. Connecting the AV Port on the HD-TX1-C and HD-RX1-C Connect the AV OUT port on the HD-TX1-C to the AV IN port on the HD-RX1-C using either of the following STP cables: DM-CBL-8G cable, which supports distances up to 330 feet (100 meters) NOTE: For optimum performance and ESD (electrostatic discharge) protection, it is recommended that DM-CBL-8G cable be used. [. . . ] 7023A (2028987) 11. 10 www. crestron. com ©2010 Specifications subject to change without notice. 888. 273. 7876 201. 767. 3400 Crestron is a registered trademark of Crestron Electronics, Inc. HDMI is a trademark or registered trademark of HDMI Licensing LLC in the United States and other countries. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE CRESTON HD-EXT1-C

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual CRESTON HD-EXT1-C will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag