User manual CRESTON MSMK-4SM INSTALLATION

[. . . ] Crestron MSMK-4SM Multi-Surface Mount Kit for the TPMC-4SM Series Installation Guide This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON Regulatory Compliance As of the date of manufacture, the MSMK-4SM has been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling. All brand names, product names and trademarks are the property of their respective owners. ©2010 Crestron Electronics, Inc. Crestron MSMK-4SM Multi-Surface Mount Kit for the TPMC-4SM Series Contents Multi-Surface Mount Kit for the TPMC-4SM Series: MSMK-4SM 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Continue with this procedure to assemble the angle mounting bracket with the glass mounting plate. Using a 1/4" hex driver, install the angle mounting bracket (2024621 or 2024622) to the glass mounting plate with the four included hex nuts (2004878). Refer to the illustration on the following page for visual guidance. NOTE: Angle mounting bracket may be oriented to tilt the touchpanel 20 degrees up or down and depending on the application. 8 · Multi-Surface Mount Kit for the TPMC-4SM Series: MSMK-4SM Installation Guide ­ DOC. 6848B Crestron MSMK-4SM Attach Angle Mounting Bracket Multi-Surface Mount Kit for the TPMC-4SM Series Glass Glass Mounting Plate (4509195 or 4509522) Angle Mounting Bracket (2024621 or 2024622) Nut (4) #04-40 Hex (2004878) 2. 3. Run the RJ-45 network wiring through the hole in the back of the plastic enclosure. Attach the plastic enclosure (2024381 or 2024382) to the angle mounting bracket with the four included #04-40 x 1/4" Phillips head screws (2007161), as shown in the illustration on the following page. Observe orientation of the TOP screening to ensure proper installation of plastic enclosure. Installation Guide ­ DOC. 6848B Multi-Surface Mount Kit for the TPMC-4SM Series: MSMK-4SM · 9 Multi-Surface Mount Kit for the TPMC-4SM Series Attach Plastic Enclosure to Angle Mounting Bracket Crestron MSMK-4SM Glass Mounting Plate (4509195 or 4509522) Glass Angle Mounting Bracket (2024621 or 2024622) Screw (4) #04-40 x 1/4" Pan Head, Phillips (2007161) Plastic Enclosure (2024381 or 2024382) NOTE: When raceway is run to the bottom of the touchpanel, the plastic cover must be placed on the top of the plastic enclosure. When raceway is run to the top of the touchpanel, the plastic cover must be placed on the bottom of the plastic enclosure. Connect the RJ-45 network wiring to the touchpanel and then install the touchpanel by carefully pressing the unit into place. While snapping the unit into place, pull the RJ-45 network wiring to remove slack. Observe orientation of the TOP screening to ensure proper installation of the plastic enclosure. Using a flathead screwdriver, carefully separate the back cover of the touchpanel from the front of the unit. Connect the RJ-45 network wiring to the touchpanel and then install the touchpanel by carefully pressing the unit into place. While snapping the unit into place, pull the RJ-45 network wiring to remove slack. Refer to the illustration below for visual guidance. 4. 5. NOTE: Use care when pulling plenum rated cable through the bottom of the plastic enclosure; the rigidity of the cable will cause slight resistance. Mount Touchpanel to Drywall with Raceway NOTE: Raceway can be run to the top or bottom of the touchpanel. NOTE: When raceway is run to the bottom of the touchpanel, the plastic cover must be inserted in the top of the plastic enclosure. When raceway is run to the top of the touchpanel, the plastic cover must be inserted in the bottom of the plastic enclosure. NOTE: Raceway is intended to be installed on smooth surfaces such as drywall or glass. 12 · Multi-Surface Mount Kit for the TPMC-4SM Series: MSMK-4SM Installation Guide ­ DOC. 6848B Crestron MSMK-4SM Multi-Surface Mount Kit for the TPMC-4SM Series 6. [. . . ] Shipments arriving freight collect or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a 15% restocking fee plus shipping costs on any products returned with an RMA. Return freight charges following repair of items under warranty shall be paid by CRESTRON, shipping by standard ground carrier. In the event repairs are found to be non-warranty, return freight costs shall be paid by the purchaser. 2. 3. CRESTRON Limited Warranty CRESTRON ELECTRONICS, Inc. [. . . ]