User manual CRESTON TPMC-12 11-10

[. . . ] Crestron TPMC-12 IsysTM 12" Tilt Touchpanel Operations Guide This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON Regulatory Compliance As of the date of manufacture, the TPMC-12 has been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling. Federal Communications Commission (FCC) Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user's authority to operate the equipment. [. . . ] Refer to "Network Wiring", "CAT5 Wiring" and "QuickMedia Wiring" on page 13 before applying power. If the TPMC-CH-IMC is to be used for connecting CAT5 audio and CAT5 video, refer to the latest revision of the TPMC-CH-IMC Operations Guide (Doc. 6345) for more information. Hardware Connections for the TPMC-12 Memory Expansion: For MMC Compatible Card Ground QM IN: QuickMedia Audio, Video and Mic Input Over CAT5 AUD I/O: Balanced Audio In and Mic Out Over CAT5 NET: To Control System and Other Cresnet Devices USB: For 3rd Party Peripherals LAN: 10BASE-T/100BASE-TX/1000BASE-T High Speed Ethernet VID IN: Balanced Video Input Over CAT5 CAUTION: Do not apply excessive pressure to the touchscreen display during handling. Doing so can crack the screen and damage the touchpanel. CAUTION: Use only the TPMC-CH-IMC Interface Module when connecting to the VID IN port. Use of the older "IMC" products, such as those with a 10-pin RJ-45 based interface, could damage the panel. Operations Guide ­ DOC. 6675B IsysTM 12" Tilt Touchpanel: TPMC-12 · 39 IsysTM 12" Tilt Touchpanel Crestron TPMC-12 NOTE: Ensure the unit is properly grounded by connecting the chassis ground lug to an earth ground (building steel). NOTE: The TPMC-12 can only be powered by the 4-position terminal block connector labeled NET. Power cannot be supplied from network devices that are connected to the mini-terminal block connectors. NOTE: The Y and Z Cresnet data lines from the network are connected to the NET connector, which is internally wired to the 4-position mini-terminal block connector at each QM connector. (Does not necessarily apply to all QM products. ) NOTE: The maximum continuous current from equipment under any external load conditions shall not exceed a current limit that is suitable for the minimum wire gauge used in interconnecting cables. The ratings on the connecting unit's supply input should be considered to prevent overloading the wiring. NOTE: Be sure to set Cresnet to Disable when using Ethernet. Refer to "Cresnet" which starts on page 20 for details. NOTE: For optimum performance, Crestron strongly recommends using CresCAT-QM cable, available from Crestron. Other high-quality/low skew CAT5e/CAT6 wiring may also be used with varying performance. NOTE: For CAT5 and QuickMedia connections, use Crestron Certified Wire. NOTE: A QuickMedia transmitter such as the QM-TX is required in order to connect conventional video and audio sources to the QM IN port. The QM port is not connected through any "IMC" interface. NOTE: TPMC-12 touchpanels include a TPMC-CH-IMC Interface Module for system connection. The TPMC-CH-IMC serves as an interface between the touchpanel, external A/V system, microphone output and the Cresnet system. Refer to the TPMC-CH-IMC Operations Guide (Doc. [. . . ] The SOFTWARE may contain NetMeeting, Remote Assistance, and Remote Desktop technologies that enable the SOFTWARE or other applications installed on the Device to be used remotely between two or more computing devices, even if the SOFTWARE or application is installed on only one Device. You may use NetMeeting, Remote Assistance, and Remote Desktop with all Microsoft products; provided, however, use of these technologies with certain Microsoft products may require an additional license. For both Microsoft products and non-Microsoft products, you should consult the license agreement accompanying the applicable product or contact the applicable licensor to determine whether use of NetMeeting, Remote Assistance, or Remote Desktop is permitted without an additional license. You agree that MS, Microsoft Corporation, and their affiliates may collect and use technical information gathered in any manner as part of product support services related to the SOFTWARE. [. . . ]