User manual CRESTON TPMC-12L

[. . . ] Crestron TPMC-12L IsysTM 12" Wall Mount Touchpanel Operations Guide This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON Regulatory Compliance As of the date of manufacture, the TPMC-12L has been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling. Federal Communications Commission (FCC) Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user's authority to operate the equipment. [. . . ] The only tool required is a #2 Phillips tip screwdriver. Do not apply excessive pressure to the touchscreen. Loosen and remove the screws that secure touchpanel to the mounting option in use. Using equal pressure, carefully remove the touchpanel from the opening. If necessary, secure and label the attached cables before disconnecting them from the back of the touchpanel. 40 · IsysTM 12" Wall Mount Touchpanel: TPMC-12L Operations Guide ­ DOC. 6686B Crestron TPMC-12L Hardware Hookup Ventilation IsysTM 12" Wall Mount Touchpanel The TPMC-12L should be used in a well-ventilated area. The venting holes should not be obstructed under any circumstances. If the TPMC-12L is hot to the touch, consider used forced air ventilation. To prevent overheating, do not operate this product in an area that exceeds the environmental temperature range listed in the table of specifications. Consideration must be given if installed in a closed or multi-unit rack assembly since the operating ambient temperature of the environment may be greater than the room ambient temperature. Contact with thermal insulating materials should be avoided on all sides of the unit. Connect the Device Make the necessary connections as called out in the illustration that follows this paragraph. Refer to "Network Wiring", "CAT5 Wiring" and "QuickMedia Wiring" on page 13 before applying power. If the TPMC-CH-IMC is to be used for connecting CAT5 audio and CAT5 video, refer to the latest revision of the TPMC-CH-IMC Operations Guide (Doc. 6345) for more information. Hardware Connections for the TPMC-12L Ground MEMORY EXPANSION: For MMC Compatible Card QM IN: QuickMedia Audio, Video & Mic Input Over CAT5 AUD I/O: Balanced Audio In & Mic Out Over CAT5 NET: To Control System and Other Cresnet Devices USB: For 3rd Party Peripherals LAN: 10/100/1000 Mbps High Speed Ethernet VID IN: Balanced Video Input Over CAT5 CAUTION: Do not apply excessive pressure to the touchscreen display during handling. Doing so can crack the screen and damage the touchpanel. CAUTION: Use only the TPMC-CH-IMC Interface Module when connecting to the VID IN port. Use of the older "IMC" products, such as those with a 10-pin RJ-45 based interface, could damage the panel. NOTE: Ensure the unit is properly grounded by connecting the chassis ground lug to an earth ground (building steel). Operations Guide ­ DOC. 6686B IsysTM 12" Wall Mount Touchpanel: TPMC-12L · 41 IsysTM 12" Wall Mount Touchpanel Crestron TPMC-12L NOTE: The TPMC-12L can only be powered by the 4-position terminal block connector labeled NET. Power cannot be supplied from network devices that are connected to the mini-terminal block connectors. NOTE: The Y and Z Cresnet data lines from the network are connected to the NET connector, which is internally wired to the 4-position mini-terminal block connector at each QM connector. (Does not necessarily apply to all QM products. ) NOTE: The maximum continuous current from equipment under any external load conditions shall not exceed a current limit that is suitable for the minimum wire gauge used in interconnecting cables. [. . . ] The SOFTWARE may contain NetMeeting, Remote Assistance, and Remote Desktop technologies that enable the SOFTWARE or other applications installed on the Device to be used remotely between two or more computing devices, even if the SOFTWARE or application is installed on only one Device. You may use NetMeeting, Remote Assistance, and Remote Desktop with all Microsoft products; provided, however, use of these technologies with certain Microsoft products may require an additional license. For both Microsoft products and non-Microsoft products, you should consult the license agreement accompanying the applicable product or contact the applicable licensor to determine whether use of NetMeeting, Remote Assistance, or Remote Desktop is permitted without an additional license. You agree that MS, Microsoft Corporation, and their affiliates may collect and use technical information gathered in any manner as part of product support services related to the SOFTWARE. [. . . ]