User manual CRESTON TPMC-9 10-10

[. . . ] Crestron TPMC-9 IsysTM 9" Tilt Touchpanel Operations Guide This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON Regulatory Compliance As of the date of manufacture, the TPMC-9 has been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling. Federal Communications Commission (FCC) Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user's authority to operate the equipment. [. . . ] Program Manager Program Manager is the view where programmers "program" a Crestron control system by assigning signals to symbols. The symbol can be viewed by double clicking on the icon or dragging it into Detail View. Each signal in the symbol is described in the SIMPL Windows help file (F1). Programming with VisionTools Touchpanel screens should be created in Crestron VisionTools® (VT Pro-e®) to allow accessing the embedded applications, switching of source signals to desired outputs as well as selection of the system mode. There are no special programming requirements to use the functions of the TPMC-9 in a room-control system. Multi-Mode Objects Multi-mode objects offer highperformance programming! The single most-advanced VT Pro-e high-performance programming technique involving the TPMC-9 is the concept of multi-mode objects. button, legend, etc. ) is an object drawn on a VT Pro-e page that can have one or more active and inactive visible settings (modes). For examples, refer to www. crestron. com/exampleprograms and search for multimode object examples. This file contains the VT Pro-e touchpanel files and SIMPL Windows files that illustrate the high-performance capabilities of multi-mode objects. WAV File Audio Messages The TPMC-9 touchpanels are capable of playing audio messages as system prompts and responses. These files are recorded as WAV files on a PC using an audio utility such as Sound Recorder that is packaged with Microsoft Windows 95/98/Me/XP/NT/2000/Vista/7TM. Files from other sources may also be converted to an acceptable format by using this or a similar utility. Many other audio utilities are available commercially or as shareware. The TPMC-9 touchpanels accept the following WAV file formats: PCM, 8 & 16 bit, 8 ­ 44. 1 kHz, mono & stereo. For more information about how to use Sound Recorder, refer to its User's Guide and Operations Guide ­ DOC. 6965A IsysTM 9" Tilt Touchpanel: TPMC-9 · 27 IsysTM 9" Tilt Touchpanel Crestron TPMC-9 extensive help information provided with the software. Also refer to the help file in VT Pro-e to learn how to use its audio tool, Sound Manager, to attach WAV files to a touchpanel project. Pre-recorded WAV files for voice prompts and responses are available from Crestron. These files can be stored into and programmed for use in the touchpanel directly or may be edited with the Sound Recorder. For example, the individual files can be combined to create custom messages. NOTE: Touchpanel WAV files can be obtained from the Wave LC Library of the Crestron FTP site. Bit Depth and File Size A balance of performance and quality can be achieved by using VT Pro-e to configure the size of graphics in a project. Read this section to learn about bit depth and how to maximize the quality and performance of a TPMC-9 project. Bit depth refers to the number of memory bits used to store color data for each pixel in a raster image. A touchpanel raster image consists of a rectangular grid of picture elements (pixels). Each pixel uses the same amount of memory to store its color data. [. . . ] Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number and return address. Products may be returned for credit, exchange or service with a CRESTRON Return Merchandise Authorization (RMA) number. Authorized returns must be shipped freight prepaid to CRESTRON, 6 Volvo Drive, Rockleigh, N. J. or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. [. . . ]