User manual CRESTON TPMC-V-IMCW INSTALLATION

[. . . ] Crestron TPMC-V-IMCW Interface Module for TPMC-V Touchpanels Installation Guide This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON Regulatory Compliance As of the date of manufacture, the TPMC-V-IMCW has been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling. Federal Communications Commission (FCC) Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user's authority to operate the equipment. [. . . ] The following guidelines are provided to ensure your safety: · When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest component at the bottom of the rack. · If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack. Installing on a Level Surface To prepare the TPMC-V-IMCW to be mounted onto a level surface, ensure the unit is attached to the surface mount bracket, as shown in the following illustration. TPMC-V-IMCW (6503939) Mounting Bracket (2016054) Screws (2) #6-32 x 3/16" (2007203) Assy, Insert, Black (4511010) or Assy, Insert, White (4510979) TPMC-V-IMCW Bracket Mount (Exploded View) 14 · Interface Module: TPMC-V-IMCW Installation Guide ­ DOC. 6939A Crestron TPMC-V-IMCW Interface Module Hardware Hookup Make the necessary connections as called out in the illustrations below. Refer to "Network Wiring" on page 10 before attaching the 4-position terminal block connector. Apply power after all connections have been made. When making connections to the TPMC-V-IMCW, use Crestron power supplies for Crestron equipment. Hardware Connections for the TPMC-V-IMCW (Front) TO PANEL VIDEO/LAN: Connect to TPMC-V12/15 Touchpanel TO PANEL NET: Connect to TPMC-V12/15 Touchpanel 24VDC 2A*: From DC Power Pack * A ferrule dust cap (2017028) is provided to cover the front panel DC power jack when not in use. Hardware Connections for the TPMC-V-IMCW (Back) LAN: 10/100BASE-T to LAN VIDEO INPUT: Balanced or Unbalanced Source NET: To Control System and Other Cresnet Devices 24VDC 2A : From DC Power Pack Installation Guide ­ DOC. 6939A Interface Module: TPMC-V-IMCW · 15 Interface Module Crestron TPMC-V-IMCW NOTE: Ensure the unit is properly grounded by connecting the chassis ground lug to an earth ground (building steel). NOTE: The TPMC-V-IMCW can be powered via the 24VDC 2A jack on either the front or the back of the unit if the NET port is not being used to power the module. 16 · Interface Module: TPMC-V-IMCW Installation Guide ­ DOC. 6939A Crestron TPMC-V-IMCW Interface Module Problem Solving Troubleshooting The following table provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative. TPMC-V-IMCW Troubleshooting TROUBLE Device does not function. POSSIBLE CAUSE(S) Device is not receiving sufficient power. CORRECTIVE ACTION Use a Crestron approved power source and verify connections. Use the Crestron Power Calculator to help calculate how much power is needed for the system. Use a Crestron approved power source and verify connections. Use the Crestron Power Calculator to help calculate how much power is needed for the system. Check that all ground connections have been made properly. PWR LED does not illuminate. Device is not receiving sufficient power. Loss of functionality due to electrostatic discharge. Improper grounding. Installation Guide ­ DOC. 6939A Interface Module: TPMC-V-IMCW · 17 Interface Module Crestron TPMC-V-IMCW Check Network Wiring Use the Right Wire In order to ensure optimum performance over the full range of your installation topology, use Crestron Certified Wire only. Failure to do so may incur additional charges if support is required to identify performance deficiencies because of using improper wire. CAUTION: Use only Crestron power supplies for Crestron equipment. Failure to do so could cause equipment damage or void the Crestron warranty. CAUTION: Provide sufficient power to the system. [. . . ] Shipments arriving freight collect or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a 15% restocking fee plus shipping costs on any products returned with an RMA. Return freight charges following repair of items under warranty shall be paid by CRESTRON, shipping by standard ground carrier. In the event repairs are found to be non-warranty, return freight costs shall be paid by the purchaser. 2. 3. CRESTRON Limited Warranty CRESTRON ELECTRONICS, Inc. [. . . ]