User manual CRESTRON C2N-IADS30X24

[. . . ] Crestron C2N-IADS30X24 Intercom Audio Distribution System Operations Guide This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. ©2006 Crestron Electronics, Inc. Crestron C2N-IADS30X24 Intercom Audio Distribution System Contents Intercom Audio Distribution System: C2N-IADS30X24 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Features and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack. NOTE: If rack mounting is not required, rubber feet are provided for tabletop mounting or stacking. Apply the feet near the corner edges on the underside of the unit. Refer to "Stacking" below for details. NOTE: Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given to supply connections other than direct connections to the branch circuit. There are screws that secure each side of the IADS top cover. Using a #2 Phillips screwdriver, remove the three screws closest to the front panel from one side of the unit. Refer to the diagram following step 3 for a detailed view. Position a rack ear so that its mounting holes align with the holes vacated by the screws in step 1. Secure the ear to the unit with three screws from step 1, as shown in the following diagram. 2. 3. Ear Attachment for Rack Mounting (Side View of Unit) FASTEN WITH THREE TOP COVER SCREWS 4. Stacking Repeat procedure (steps 1 through 3) to attach the remaining ear to the opposite side. Four "feet" are provided with the IADS so that if the unit is not rack mounted, the rubber feet can provide stability when the unit is placed on a flat surface or stacked. These feet should be attached prior to the hookup procedure. Refer to the following illustration for placement of the feet. 10 · Intercom Audio Distribution System: C2N-IADS30X24 Operations Guide - DOC. 6170A Crestron C2N-IADS30X24 Intercom Audio Distribution System Feet Location (Bottom View of Unit) ATTACH FEET NEAR CORNERS OF THE UNIT Connect the Device Make the necessary connections as called out in the illustration that follows this paragraph. Refer to "Network Wiring" on page 9 before attaching the 4-position terminal block connector. Apply power after all connections have been made. When making connections to the IADS, use Crestron power supplies for Crestron equipment. Hardware Connections for the C2NIADS30X24 Operations Guide ­ DOC. 6170A Intercom Audio Distribution System: C2N-IADS30X24 · 11 Intercom Audio Distribution System Crestron C2N-IADS30X24 Programming Software Have a question or comment about Crestron software?Answers to frequently asked questions (FAQs) can be viewed in the Online Help section of the Crestron website. To post a question or view questions you have submitted to Crestron's True Blue Support, log in at http://support. crestron. com. [. . . ] or its authorized subsidiaries, with RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a 15% restocking fee, plus shipping costs, on any products returned with an RMA. Return freight charges following repair of items under warranty shall be paid by CRESTRON, shipping by standard ground carrier. [. . . ]