User manual CRESTRON CAEN

[. . . ] Weight is specified in pounds and kilograms (in parentheses). The lower keyholes are not symmetrically spaced within singlewide enclosures. Weight (empty) is the weight of an empty enclosure with cover. W6 W3 W5 D1 3. Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 Tel: 888. CRESTRON Fax: 201. 767. 7576 www. crestron. com Installation Guide ­ DOC. [. . . ] This includes complete in factory system configuration and assembly by Crestron for an additional fee. NOTE: Install modules into the lowest available spaces and continue toward the top of the enclosure. NOTE: Enclosures are intended for indoor use only. NOTE: When flush mounting, 5/8" drywall is preferred. Crestron CAEN Tighten all CLT-Series terminal block screws and grounding terminal block screws to the torque specified in the Torque Data table. CAUTION: Failure to properly tighten the screws may result in poor electrical connection and overheating of the terminals. Torque Data CLT Terminal Blocks Wire Range Torque (In-Lbs) 22 - 10 9 Grounding Terminal Blocks 14 - 10 35 8 40 6-4 45 Key ­ Typical Products in a CAEN Enclosure CLX-SERIES CLT-SERIES TERMINAL MODULE BLOCKS PROFESSIONAL GROUNDING TERMINAL AUTOMATION BLOCKS COMPUTER Mounting Details - Single-Wide CAEN Wiring CAUTION: All power feeds must be protected by 15 or 20 amp circuit breakers (supplied by others). NOTE: Use copper conductors only ­ rated 60°C NOTE: All wiring must be installed in accordance with all local and national electrical codes. If required, insert into knockouts at the bottom of the enclosure to prevent damage to low voltage wiring. Class 1 and Class 2 field wires must be kept separate. Refer to the following illustrations showing single-wide and double-wide wiring details. Areas for high voltage (Class 1) wiring are shown along the top and side(s) of the unit. The lower area is reserved for low voltage (Class 2) wiring. MOUNT CLT TO THIS COLUMN CLT TERMINAL BLOCKS MUST BE MOUNTED TO THE HOLES SHOWN ABOVE 2 · Automation Enclosures: CAEN Installation Guide ­ DOC. 5940C Crestron CAEN Wiring Details - Single-Wide CAEN CLASS 1 WIRING ONLY Automation Enclosures Mounting Details - Double-Wide CAEN C L A S S 1 W I R I N G O N L Y MOUNT CLT TO THIS COLUMN MOUNT CLT TO THIS COLUMN CLASS 2 WIRING ONLY CLT TERMINAL BLOCKS MUST BE MOUNTED TO THE HOLES SHOWN ABOVE Wiring Details - Double-Wide CAEN CLASS 1 WIRING ONLY C L A S S 1 W I R I N G O N L Y C L A S S 1 W I R I N G O N L Y CLASS 2 WIRING ONLY Installation Guide ­ DOC. 5940C Automation Enclosures: CAEN · 3 Automation Enclosures Further Inquiries If you cannot locate specific information or have questions after reviewing this guide, please take advantage of Crestron's award winning customer service team by calling the Crestron corporate headquarters at 1-888-CRESTRON [1-888-273-7876]. For assistance in your local time zone, refer to the Crestron website (www. crestron. com) for a listing of Crestron worldwide offices. You can also log onto the online help section of the Crestron website to ask questions about Crestron products. First-time users will need to establish a user account to fully benefit from all available features. Crestron CAEN Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange, or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact the factory and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address. Products may be returned for credit, exchange, or service with a CRESTRON Return Merchandise Authorization (RMA) number. [. . . ] In no event shall CRESTRON be liable for incidental or consequential damages of any kind (property or economic damages inclusive) arising from the sale or use of this equipment. CRESTRON is not liable for any claim made by a third party or made by the purchaser for a third party. CRESTRON shall, at its option, repair or replace any product found defective, without charge for parts or labor. Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the unexpired portion of the warranty. [. . . ]