User manual CRESTRON CAGE2

[. . . ] 10 Future Updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Return and Warranty Policies. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Merchandise Returns / Repair Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 CRESTRON Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] However, the blank plate will not be reused. Use a #2 Phillips screwdriver to remove four rear-mounting SEM screws that secure the AV2 blank plate and remove the plate. CAGE2 Installation (3 of 11) - Remove Rear-Mounting SEM Screws & AV2 Blank Plate NOTE: During the next step, the two screws must be retained to install the CAGE2. However, the two nuts will not be reused. From inside the AV2, use a 1/4-in hexdriver or wrench to hold the nut of one of the bottom-mounting screws. From the underside of the AV2, use a #2 Phillips screwdriver to remove the mounting screw. Repeat for second nut and screw. CAGE2 Installation (4 of 11) - Remove Bottom-Mounting Screws & Nuts Installation Guide - DOC. 5964 3-Card Expansion Cage for AV2: CAGE2 · 5 3-Card Expansion Cage for AV2 6. Crestron CAGE2 Refer to the diagram below. Attach either long-edge of the supplied PCB jumper to the interconnect connector (J1) on the CAGE2. CAGE2 Installation (5 of 11) - Attach PCB Interconnect Jumper to CAGE2 J1 7. Refer to the diagram below. Rotate the CAGE2 assembly until the CAGE2 connector backplane is towards the AV2 front panel and position into AV2. CAGE2 Installation (6 of 11) - Position CAGE2 Assembly into AV2 6 · 3-Card Expansion Cage for AV2: CAGE2 Installation Guide - DOC. 5964 Crestron CAGE2 8. 3-Card Expansion Cage for AV2 Refer to the diagram below. Align the PCB jumper to the AV2 processor board connector and slide the CAGE2 assembly towards rear of AV2. Make sure that PCB jumper is inserted into the AV2 connector and align the CAGE2 bottom and rear mounting holes. CAGE2 Installation (7 of 11) - Slide CAGE2 Assembly Rearwards 9. Refer to the diagram below. Install the two bottom-mounting screws that were removed in step 5 to finger-tight then, using a #2 Phillips tip screwdriver tighten the screws an additional 1/8-turn. CAGE2 Installation (8 of 11) - Install Bottom-Mounting Screws Installation Guide - DOC. 5964 3-Card Expansion Cage for AV2: CAGE2 · 7 3-Card Expansion Cage for AV2 Crestron CAGE2 10. Re-install the the four rear-mounting SEM (attached washer) screws that were removed in step 4 to finger-tight then, using a #2 Phillips tip screwdriver tighten the screws an additional 1/8-turn. CAGE2 Installation (9 of 11) - Re-install Rear-Mounting Screws 11. NOTE: The AV2 cover side screws are 0. 375 in long and the cover top screws are 0. 250 in long. Make sure that the correct screws are re-installed in the cover side and top, respectively. Re-install the six cover screws that were removed from each side of the AV2 in step 2 to finger-tight then, using a #2 Phillips tip screwdriver tighten the screws an additional 1/8-turn. CAGE2 Installation (10 of 11) - Re-install Cover Side Screws 13. Re-install the four cover screws that were removed from the top of the AV2 in step 1 to finger-tight then, using a #2 Phillips tip screwdriver tighten the screws an additional 1/8-turn. 8 · 3-Card Expansion Cage for AV2: CAGE2 Installation Guide - DOC. 5964 Crestron CAGE2 3-Card Expansion Cage for AV2 CAGE2 Installation (11 of 11) - Re-install Cover Top Screws 14. Refer to the installation and operation guide supplied with the expansion card for card installation instructions. If more than one plugin expansion card is to be utilized in the AV2, additional face-plate(s) of the CAGE2 must be removed. SIMPL Windows Programming SIMPL (Symbol Intensive Master Programming Language) is an easy-to-use programming language that is completely integrated and compatible with all Crestron system hardware. [. . . ] Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the unexpired portion of the warranty. Except as expressly set forth in this warranty, CRESTRON makes no other warranties, expressed or implied, nor authorizes any other party to offer any warranty, including any implied warranties of merchantability or fitness for a particular purpose. Any implied warranties that may be imposed by law are limited to the terms of this limited warranty. This warranty statement supercedes all previous warranties. Trademark Information All brand names, product names, and trademarks are the sole property of their respective owners. [. . . ]