User manual CRESTRON CHV-RTS CHV-RTHS

[. . . ] Functional Summary · · · · Small and unobtrusive face allows blending into any décor Primed white, may be used as is, painted, or wallpapered Easy one-piece mounting (additional hardware not required) Readily connects to thermostat with two non-polarized wires Remote Temperature/Humidity Sensors · 1 Installation Guide - DOC. 8189A Remote Temperature/Humidity Sensors Crestron CHV-RTS/CHV-RTHS Specifications SPECIFICATION Temperature Range (CHVRTS and CHV-RTHS) Humidity Range (CHVRTHS only) DETAILS -30º to 120ºF (-34. 44Cº to 48. 89ºC)* 0 to 100% *Thermostat front panel indoor temperature display is limited to a range of 0 ­ 110ºF (-18º to 43ºC). The front panel outdoor thermostat display will display the full range of temperature. Physical Description Refer to the illustrations below and on the following page. The face of the sensor is 1. 5 in (3. 81 cm) wide. [. . . ] In situations where ordinary two-conductor thermostat wire (18 to 20 gauge) has been installed, it may be used for runs up to 100 feet (30. 48 meters). This is not a preferred method of installation. Other cable types are satisfactory, provided the total capacitance is less than 7000 pF. Connect the wires from the thermostat to the 10 in (25. 4 cm) sensor pigtail (22 AWG x12" black/black twisted pair) using wire nuts. (Refer to "Hardware Hookup" on page 5). 4 · Remote Temperature/Humidity Sensors Installation Guide ­ DOC. 8189A Crestron CHV-RTS/CHV-RTHS Remote Temperature/Humidity Sensors 7. Press fit the sensor into the hole; the clips on either side of the sensor hold it in place. Wire Nuts Pigtail Wires from Sensor Wires from Thermostat Mounting Clips 1in (2. 54cm) Hole NOTE: The face of the sensor may be painted or wallpapered to match the wall. However, keep the small gap around the outer edge clear of any obstructions. Hardware Hookup The sensors are connected to the remote sensor terminals RS1, RS2, and a common connection RSR on the rear plastic housing of the thermostat. Separate the thermostat from its backplate. The thermostat terminal blocks mate to pins protruding out of the front thermostat assembly. Thermostat firmware release 1. x supports the addition of only two optional remote sensors (temperature and/or temperature/humidity) per thermostat on sensor inputs RS1 and RS2. Thermostat firmware release 2. x supports up to four optional temperature (CHV-RTS) or slab sensors (CHV-RSS) or two temperature/humidity sensors (CHV-RTHS). If you are using one temperature/humidity sensor, then you may add two temperature sensors (CHV-RTS or CHV-RSS) to the other sensor input. Installation Guide - DOC. 8189A Remote Temperature/Humidity Sensors · 5 Remote Temperature/Humidity Sensors Crestron CHV-RTS/CHV-RTHS Connection Example 1: Connecting two temperature/humidity sensors to the thermostat (maximum number of temperature/humidity sensors): NOTE: Sensor wiring is non-polarized 1. Remote sensor 1 connected to RS1 and RSR 2. Remote sensor 2 connected to RS2 and RSR Remote Sensor 1 Remote Sensor 2 TOP 24(C) RHU 24(R) HUM RSR RSR RS1 RS2 24V Y G Z Thermostat Backplate NETWORK Connection Example 2: Connecting four temperature sensors (CHV-RTS) to the thermostat (maximum number of temperature sensors): 1. Remote Sensor 1 and 3 are connected to RS1 and RSR. Remote Sensor 2 and 4 are connected to RS2 and RSR. Remote Temperature Sensor 4 Remote Temperature Sensor 3 Remote Temperature Sensor 2 Remote Temperature Sensor 1 TOP 24(C) RHU 24(R) HUM RSR RSR RS1 RS2 24V Y G Z Thermostat Backplate 6 · Remote Temperature/Humidity Sensors NETWORK Installation Guide ­ DOC. 8189A Crestron CHV-RTS/CHV-RTHS Remote Temperature/Humidity Sensors Connection Example 3: Connecting one temperature/humidity sensor (CHV-RTHS) and two temperature sensors (CHV-RTS) to the thermostat (maximum number of sensors when using one temperature/humidity sensor): 1. Remote Temperature/Humidity Sensor 1 is connected to RS1 and RSR. Remote Temperature Sensor 1 and 2 are connected to RS2 and RSR. Remote Temperature Sensor 2 Remote Temperature/Humidity Sensor 1 Remote Temperature Sensor 1 TOP 24(C) RHU 24(R) HUM RSR RSR RS1 RS2 24V Y G Z Thermostat Backplate NETWORK NOTE: For additional firmware details, refer to the latest version of the Crestron CHV-TSTAT/CHV-THSTAT Thermostats Operations and Installation Guide, Doc. 8163, and CHV-RSS Slab Sensor Installation Guide, Doc. [. . . ] Shipments arriving freight collect or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a 15% restocking fee, plus shipping costs, on any products returned with an RMA. Return freight charges following repair of items under warranty shall be paid by CRESTRON, shipping by standard ground carrier. In the event repairs are found to be non-warranty, return freight costs shall be paid by the purchaser. 2. 3. CRESTRON Limited Warranty CRESTRON ELECTRONICS, Inc. [. . . ]