User manual CRESTRON CHV-TSTAT CHV-THSTAT FIRMWARE 2.0 AND LATER

[. . . ] Crestron CHV-TSTAT & CHV-THSTAT Thermostats Operations and Installation Guide This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. ©2004 Crestron Electronics, Inc. Crestron CHV-TSTAT and CHV-THSTAT Thermostats Contents Quick Installation Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii Thermostats: CHV-TSTAT and CHV-THSTAT 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Functions and Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Disable Auto Mode: Will not display Auto on System Mode screen and will not permit entering the auto mode even from Cresnet commands. SENSORS SETUP: SENSORS Sensor >TEMP HUM Internal: OMIT USE Remote 1: SLAB DETECTED: 1 x T Remote 2: Choose USE or OMIT (Built-in Sensors Only) Choose USE, OMIT, OD, or SLAB (Remote Sensors Only) NOTE: Remote 1 and Remote 2 options do not appear on this screen if these sensors are not connected. SERVICE/TEST SETUP: SERVICE/TEST Slab Heat Call: OFF Space Heat Call: OFF Space Cool Call: OFF Humidifier Call: OFF Fan Call: OFF Press MODE button to return to the first screen Or Press and hold the MODE and VIEW buttons simultaneously for five seconds to exit Setup. NOTE: You cannot exit if the sensor setup does not meet system requirements. NOTE: This screen bypasses all system delays and is used by the installer to manually operate the HVAC system. Only one system can be run at a time. Operations and Installation Guide ­ DOC. 8163C Thermostats: CHV-TSTAT and CHV-THSTAT · 51 Thermostats Crestron CHV-TSTAT and CHV-THSTAT Slab 5B ­ 1 Stage Heat/Cool with Floor Warming (Heat Pump) Press and hold the MODE and VIEW buttons simultaneously for five seconds to enter setup mode. Slab mode 5B requires a slab remote sensor and an air temperature sensor. SYSTEM SETUP SETUP: SYSTEM Heat Sys Type: SLAB 5B Slab Reg: 6 HP/AUX or DF: HP/Aux 1 STG SPACE HEAT - COOL W/ FLOOR WARMING (HEATPUMP) SLAB=W1 HT/CL=Y1/O/G Heat System Type: SLAB 5B Slab Regulation: (1 ­ 6) 1 = Narrow temperature regulation 6 = Wide temperature regulation Heat Pump/Aux or Dual Fuel SYSTEM PERFORMANCE SETUP: SYSTEM PERF Heat Anticipator: 5 Cool Anticipator: 6 Intrstg Differential: 0. 50 HP Balance Pt: Off AUX Balance Pt: 10 Anticipators: (valid selections are 1 through 6) Low number = more frequent cycles and faster response (tighter regulation). High number = less frequent cycles and slower response (looser regulation). Interstage Differential: 0. 5 to 8. 0ºF. The proportional temperature error to trigger the second (Aux) stage. HP Balance Point - Minimum outdoor temperature at which the heat pump runs (requires outdoor sensor). AUX Balance Point - Maximum outdoor temperature at which Aux Heat System supplements the heat pump (requires outdoor sensor). HUMIDIFIER OPTIONS SETUP: HUM OPTS Show Hum Mode Pg: Show Hum View Pg: Cold Weather Comp: SYSTEM ENABLE/DISABLE PAGE Y Y N Show Hum Mode Pg and Show Hum View Pg: Select Y to show humidity page in normal operation. Cold Weather Compensation: Modifies the humidifier output to prevent condensation on the windows. Requires an outdoor temperature source (CHV-THSAT, or CHV-TSTAT with CHV-RTHS, CHV-RTS, or CHV-RSS). 52 · Thermostats: CHV-TSTAT and CHV-THSTAT Continued on following page. Operations and Installation Guide ­ DOC. 8163C Crestron CHV-TSTAT and CHV-THSTAT Thermostats Slab 5B ­ 1 Stage Heat/Cool with Floor Warming (Heat Pump) (Continued) DEVICE OPTIONS SETUP: DEVICE OPTS Network ID: 2A LCD Contrast 5 CHV-THSTAT [v2. 0, #D8000000] Select Network ID: Valid entries are 03 to FE in Hex to match the network ID set for the thermostat in SIMPL Windows. LCD Screen Contrast: 1 Lighter through 10 Darker Displays Model Number, Firmware version, and TSID number. SCREEN OPTIONS SETUP: SCRN OPTIONS Disp Global Page: Y Disp Outdoor Page: Y Disp Rem Func Pg1: Y Disp Rem Func Pg2: Y Reverse SMODE Dir N Global Page ­ Temperature & humidity selection for entire house if part of a Cresnet system. Outdoor Page ­ Temperature & humidity of the outside sensor. Remote Function Page 1, 2 ­ Allows remote control of other functions (for example: lights, alarms, etc. ). Reverse SMODE Dir ­ Allows arrow keys to select mode functions in both directions. [. . . ] Shipments arriving freight collect or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its sole and absolute discretion to charge a 15% restocking fee, plus shipping costs, on any products returned with an RMA. Return freight charges following repair of items under warranty shall be paid by CRESTRON, shipping by standard ground carrier. In the event repairs are found to be non-warranty, return freight costs shall be paid by the purchaser. 2. 3. CRESTRON Limited Warranty CRESTRON ELECTRONICS, Inc. [. . . ]